Advertisement
This product uses PTC heating, send heats by hot air, which can quickly increase room temperature. No open flame, safe, efficient and energy saving.
Product Name: Bladeless Heater Fan | Model: SKJ-CR018H |
Rated voltage: 220-240V~ | Cool mode Power: 30W |
Rated power: 1800W | Oscillating Angle: 80° |
Rated frequency: 50/60Hz | Timer: 1-8h |
The device can be switched on and off by pressing the "ON & OFF" button | |
Press Sleep mode button on the remote control. The display shows L and the wind speed become minimum. Press again to exit the sleep mode. (You can also exit the current mode by pressing the Wind Strength + button.) | |
Press Strong mode button on the remote control. The display shows H and the wind speed become max. Press again to exit the sleep mode. (You can also exit the current mode by pressing the Wind Strength + button.) | |
Press the Oscillation button to turn on the oscillation function. This fan can swing left and right 80. Press this button again to stop oscillating. | |
Press button to turn off tone of fan. The fan cancel"didi" sound. | |
Press this button to activate the cooling mode. Note: The default start mode is the cooling mode. | |
Press the "+" button on the left side of the remote control to increase the volume of air, press the "-" button on the left side of the remote control to decrease the airflow. Cool mode can be used for 9-level settings, warm mode can be set for 4 levels. | |
Press this button to activate the warm mode. Note: In warm mode there is no strong mode and sleep mode. | |
In warm mode, press the temperature button on the right side of the remote control to set the temperature. Note: this button does not work in cool mode. | |
Press the timer button on the remote control to set 1 to 8 hours of timing. |
The remote control should be pointed at the remote control signal receiver on the display to maximize the remote control signal.
Effective distance: 5M
A phenomenon that occurs due to the overlap of the frequencies of the remote control, in order to avoid misuse, please operate remotely:
The switch on remote will turn this fan to standby, not complete shutdown. Use the switch on the main unit to completely power off when this fan not in use.
If this fan not in use for a long time, please unplug the power cord.
Press the warm mode button and the display shows the ambient temperature.
Press the temperature button to set the temperature, and the display will flash digitally, which can be set to 1-30°C.
Set temperature should be higher than the ambient temperature, so that the heating function will be turned on;
When the ambient temperature reaches the set temperature, the heating function will stop and keep run for 40s, then turn to standby mode;
The ambient temperature is lower than the set temperature and the heating function will automatically activate.
Set temperature > ambient temperature: heating function on.
Set temperature ≤ ambient temperature: heating function stops
Note: The default setting temperature is 25°C. In the warm mode, when the ambient temperature is below 0°C, the display only shows 01, do not display negative temperature value. The warm air mode run over 9 hours, the machine will automatically stop running. Restart by pressing the host power button or by using the remote control.
Warm mode: use remote to set temperature, host does not support this operation.
Insert the plug into socket, turn on power switch and the machine enters the standby state:
Click the power button of the host, the buzzer will prompt you to click, and the fan will start running. Press and hold the power button for 2 seconds, the buzzer will prompt you twice, and then stop running after you release the hand.
Air Volume Shift
When host is in operation: click the main power button to switch the air volume from 1 to 9. In warm mode the air volume can set from 1 to 4.
Oscillating operation
Press and hold the power button for 1 second, the buzzer will beep once and fan start oscillating.
Press and hold the power button for 1 second again, the buzzer will beep once and fan stop oscillating.
Location
Please place the fan in a horizontal position. If there is a slope, should on a soft surface to avoid fan falling over; please do not use in high temperature and humidity (bathroom, kitchen).
Safety System: this heater fan includes an overheat protection sensor and an automatic fail-safe that cuts power to the unit if it's accidentally tipped over or overheat. If this sensor is triggered, unplug the machine and allow the fan cool. Check and remove any obstructions before restarting the heater fan and be sure to place them on a hard, level surface.
Battery installation method
Please insert the battery correctly
Malfunction phenomenon | Cause Analysis |
Plug in the power but fan not work | IS the plug properly inserted into the socket? |
Remote does not work | The battery is dead? Is the battery installed correctly? Is the remote control aligned with the signal receiver? |
Unplug the power supply before performing maintenance.
Please do not put the fan on the water or splash it, which may cause the machine be damaged. Do not use banana oil, benzine, alcohol, bleach or metal objects to wipe the surface of the fan, which may cause discoloration of the surface.
Wipe the surface with a soft, dry cloth; If especially dirty, dilute with a mild detergent and wipe with a soft cloth. Then wipe with a dry soft cloth.
Use a soft brush or a vacuum cleaner to clean the dust at the air inlet and outlet. Please clean it when there is less dust. Too much dust is not healthy and will reduce fan efficiency.
Gently wipe the surface of the remote with a soft, dry cloth. If you don't use it for a long time, avoid battery consumption. Please remove the battery inside the remote control.
Not used for a long time can be placed in a plastic bag after clean; Please avoid vibration place(car trunk.) and electrical appliances with cooling/heating functions; Please avoid placing it in direct sunlight, high temperature and humidity; Please keep out of reach of young children.
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical shock and injury to persons, including the following:
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download ULTTY SKJ-CR018H - Bladeless Fan with Heating Function Manual
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the SKJ-CR018H that isn't answered in the manual? Leave your question here.