Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for ElproSys EVC10 Series
- Page 1 Electric Vehicle AC Charger EVC10 Series (EU) - User Manual...
-
Page 2: Important Safety Instructions
USER MANUAL USER MANUAL 1. Important Safety Instructions • Risk of electric shock. Do not remove cover or attempt to open the enclosure of the device. No user serviceable parts inside. Refer servicing to qualified service personnel. • To reduce the risk of serious injury or death and damage to the charge, this device should be This charger complies with IEC61851 and CE-LVD. -
Page 3: Basic Interface
USER MANUAL USER MANUAL 2. Basic Interface 3. Dimensions 250.0mm 130mm LED Light Indication 350.0mm Rear Notch 72mm 4-Φ9mm 122mm Charging Cable Inlet Charging Cable Inlet LAN Cable Inlet... -
Page 4: Specification
USER MANUAL USER MANUAL 4. Specification 5. Status Description of the Charger Indication Light EVC10 Version Model Name Rated Input Voltage 230VAC±10% / Single Phase 400VAC+10% / Three Phase Standby - Blue Light Rated Output Current 16/32A The READY light stays steady in AC Power Frequency 50/60 Hz READY... -
Page 5: Product Name
RFID Card (RFID Version Only) 6. Packing List 7 Installation Instructions EVC10 Series (EU) - User Manual 7.1 Safety Requirements • Be sure to preview the user manual and ensure local building and electrical codes are reviewed before installing the AC charger. -
Page 6: Installation Steps
USER MANUAL USER MANUAL 7.2 Installation Steps Step 3: Tighten 13 screws on the front cover after the front cover is put back, the recommended screw torque is 1.0 N.m (9.6 lbf.in) (for 4G Version). Step 1: Use screwdriver to loosen the 13 fixed screws on the rear of charger, then remove the front cover (for 4G Version). - Page 7 USER MANUAL USER MANUAL 7.3 Wiring For safe use of electricity, please add circuit breaker protection in the input part of charging pile. Connect the L1 lead to the grid L1, connect the L2 lead to the grid L2, For safe use of electricity, please add circuit breaker protection in the input part connect the L3 lead to the grid L3, connect the N lead to the grid N, connect the PE lead of charging pile.
-
Page 8: Tools And Materials Required
USER MANUAL USER MANUAL 7.4 Tools and Materials Required 7.5 Wall-Mounted Bracket Installation Step 1: Tools required before installing the Wall-Mounted charger, gather the following tools: • Set the positions of the 4 screw holes and drill them, with a diameter of 8mm and •... -
Page 9: Operating Procedures
USER MANUAL USER MANUAL 8. Operating Instructions Step 3: Fix two M5 screws to complete the installation. 8.1 Operating Procedures ● User authorization ● Connect to Vehicle Charging Inlet ● Charging Message ● Charging completed 8.2 Operating Steps Step 1 / Standby Mode After power-on, blue light (READY), green light (CHARGE) and red light (FAULT) all lit. -
Page 10: Error And Warning Message
USER MANUAL USER MANUAL 8.3 Error and Warning Message Status Remark Input OVP 1 flashes followed by 3 sec pause Auto Recover Input UVP 2 flashes followed by 3 sec pause Auto Recover Output OCP 3 flashes followed by 3 sec pause Auto Recover 4 flashes followed by 3 sec pause Auto Recover... -
Page 11: Maintenance And Repair
USER MANUAL USER MANUAL 9. Maintenance and Repair • During the warranty period for any malfunction caused by normal use according to the User Manual and Service Instruction (to be determined by certified maintenance technicians of Joint 9.1 Daily Maintenance Technology), the product shall be repaired free of charge.
Need help?
Do you have a question about the EVC10 Series and is the answer not in the manual?
Questions and answers