Advertisement
WARNING! DO NOT use the heater near flammable material, liquids, solids, gases or compressed gas cylinders etc.
‰
Use this heater on a horizontal and stable surface.
9
DO NOT place the heater close to a bath, wash basin, shower, swimming pool or any other water-filled area or wet surface.
8
DO NOT place the heater up against any surface such as a wall, door or furniture etc.
8
The heater must not be located immediately below a socket outlet.
8
DO NOT place the heater on a raised surface or anywhere where it could topple over.
8
DO NOT get the heater wet or use in areas of high condensation.
8
DO NOT allow the power lead to touch hot surfaces.
8
DO NOT connect the heater to a timer device or other equipment than can automatically switch the heater on or off.
8
DO NOT operate the heater when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT stand on the heater.
8
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a
9
hazard.
DO NOT use the heater with wet hands or when there is water on the power cord.
8
DO NOT use the heater for anything other than its intended purpose. It is designed to provide heat in enclosed areas such as workshops
8
and other industrial areas. It is not suitable for drying clothes or laundry.
Position the heater at least a minimum of 1m at the front, rear and sides from any walls or objects.
9
If an extension cable is required it must be of the same cross section as the heater cable. It must be as short as possible and fully
9
unwound.
Ensure that the heater is correctly turned off when not in use and store in a safe, dry, childproof location.
9
1.4.
OPERATIONAL PRECAUTIONS
The heater must only be used by people who have read these instructions and have been trained in its use.
9
DO NOT obstruct the air inlet and outlet sections of the heater.
8
WARNING! In order to avoid overheating, DO NOT cover the heater.
‰
DO NOT use the heater without the grille fitted.
8
DO NOT use if the heater has been dropped.
8
DO NOT use if there are visible signs of damage to the heater.
8
DO NOT touch the heater casing or grille when first switched off, as these will be very hot and will take time to cool.
8
NOTE: Children of less than 3 years should be kept away unless supervised continuously.
Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in
its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the
appliance or perform user maintenance.
CAUTION: Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and
vulnerable people are present.
NOTE: This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a
safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be
made by children without supervision.
2.
INTRODUCTION
Electric fan heater for industrial applications. One heat setting with thermostat control, plus fan only. A totally dry heat with no
condensation, no gas, no fumes and no smell. Ideal for workshops and garages. Supplied with power cable and 3-pin plug.
3.
SPECIFICATION
Model No: ....................................................... EH2001.V2
Fuse Rating: ................................................................ 13A
Heated Area: ............................................................. 40m³
Output: ............................................................ 6,800Btu/hr
Power Supply Cable Length: ......................................1.5m
Supply: .............................................................230V - 13A
IMPORTANT! This unit is designed to raise the ambient temperature of an entire room, the temperature of the air coming out of the
front of the heater will be warmer than the general temperature of the room, but there may not be a significant increase due to the large
volume of air passing over the element. For the same reason, the element is hot during operation, but does not visibly glow. The room
temperature depends on room size, insulation and the ambient temperature, which will increase as the room gets warmer.
4.
OPERATION
4.1.
Position heater in an upright position on a firm surface and at a safe distance from any obstructions, flammable substances etc. Keep to a
minimum of 0.5m clearance at the rear and sides, and 2m clearance at the front.
4.2.
Connect the heater to a suitable mains supply.
4.3.
Set the thermostat dial to its maximum setting (fully clockwise).
4.4.
The heater will switch on when the power setting dial is set to the heater setting.
NOTE: It will take up to three minutes for the heater to reach optimum temperature.
4.5.
Once the room reaches the required temperature, turn the thermostat dial slowly counter-clockwise until the thermostat clicks, leave the
dial in this position to maintain the room temperature at this setting. The heater will continue to operate until the power switch is turned to
the OFF position.
4.6.
For fan only operation, turn the power/fan selector to the fan only setting, and set the thermostat to its minimum setting.
4.7.
When not in use, disconnect the heater from the mains supply. Store it in a safe, dry, childproof location.
© Jack Sealey Limited
Original Language Version
EH2001.V2
Issue 2 (4,F)
13/07/23
Advertisement
