Sylvania 6240VE Owner's Manual

SYLVANIA i,yeo need addi al ope aO aeeie*ance after i
reading this owner's manual or to order replace- II •
- r_sories, pleasecall ' II "
TOLL F REE: 1 -8'0o-ese-z42e I li
or visit our web site at http://www.funaFcorp.com
II
•
1. Before using your VCR
Owner's ManNam
Video Cassette Recorder
"!""-',,1'""_,,,,,_ (Back of TV
mfcharmed 3 is already occupied for broadcasting,
Hint
1) Set your TV to channel 4 ............................. ,,,,,,,,
2) Insert a pre-recorded tape into the VCR. . The RF output channel may
not change when you adjust
3) Press the PLAY button once. tracking during playback. In
4) After a few seconds, press the PLAY button on the VCR for 3 seconds, this case, stop the playback,
" The RF output channel will change to channel 4 from channel 3 and you will and start the playback again.
see a playback picture. After that, press the PLAY but-
ton on the VCR for 3 seconds
When a picture does not appear on the TV screen, repeat step [4]. again.
5) Press the STOP button to stop playback.
Cable A_na =_Back of VCR)
Signal
[1
= or
RF Cable (supplied)
(Back
Plug the AC power cords of the VCR and TV into the AC outlets.
You can use the AUDIO OUT jack and
VIDEO OUT iack on the back of the
VCR if your TV has AudioNideo Input
iacks. In this case, you need to set the
TV to external Line Input Mode. Please
refer to your TV's owner's manual.
Select this connection when you want to view or record a
scrambled channel. With this connection, channels cannot
be changed on the VCR. Youcan view or record ONLY the
channels you have selected on the cable box or the satellite
box.
• While you are recording, only the recorded channel can
be viewed.
To select channels of the cable box or satellite box
1)Turn on the VCR by pressing the POWER button, and
then, press the VCR/TV button.The POWER and the
VCR/TV indicators on the front panel will light on. Then,
press the CHANNEL buttons to select channel 3 or 4
(the same channel as the output channel d the cable
J
i Select this connection when you want to change channels
i on the VCR. With this connection, you may watch one
:"channel while recording another.
i •You may not view or record a scrambled channel.
.: To select channels of the cable box or satellite box
i 1)At the cable box or satellite box, select channel 3 or 4
:" (the same channel as the VCR's RF output channel.)
i • Refer to "RF Output Channel".
i 2)At the TV, select the same channel as the output chain
nel (3 or 4) of the cable box or satellite box.
i 3)Turn on the VCR by pressing the POWER button, and
:" then, press the VCR/TV button .The POWER and
box or satellite box). i VCR/TV indicators on the front panel will light on. Then,
• If you use the channel 4, you need to change the VCR's i select the channel you want to view or record.
RF output to channel 4. Refer to "RF Output Channel". i To play back a tape
2) At the TV, select channel 3 or 4 (the same channel as i Follow the steps 1) to 2) above. Then, play back a tape.
you have selected at step 1). _ • Refer to "Playback" on page 5.
3) At the cable box or satellite box, select the channel you i To view one channel while recording another
want to view or record. ! 1)While you are recording on the VCR, press the VCR/TV but*
:" ton so that the VCR/TV indicator disappears on the VCR.
i 2)At the cable box or satellite box, select the channel you
want to view.
(Back of TV)
(not sup?lied)
(Back of VCR)
Install two AA batteries
/z'b..
(supplied) matching the _" .'-_ .">_
polarity indicated e
the bottom of the
remote control. -,.4_
Printed in China
0VMN03900/HF310UD *****
• Remote control • RF Cable • Owner's Manual
(NA371UD) with (WPZ0901TM002) (0VMN03900)
Two AA batteries
AUDIO OUT jack AUDIO IN jack
Connect the audio cable to the audio in jack Connect the audio cable from the audio out
efacamcorder, anotherVCR, asteree _ [_jackofacamcerder anetherVCR oran
amplifier, or an audio system, i I /audiosource.
[8'1 _Ul__ f I._ool (_o'. Connect your antenna or cable box.
i _ _, d ;_ ".* ANT OUT jack
_tj L, _ Connect the RF cable (supplied) to
• I_,o_o/ '"__:_--;_theantenna n utjackon ourTV
.................. P Y •
VIDEO OUT jack _ /
Connect the video cable to the video in jack / VIDEO IN lack
of a camcorder, another VCR, or a TM / Connect th'e video cable from the video out
/ jack of a camcerder, anotherVCR or an
audio-visual source aser disc player,
vioeo disc 3layer, etc.).