Advertisement
Open the charging case, the white lights will illuminate for 1 second. The earbuds will automatically power on.
While earbuds are in an off state, touch and hold the touch strip of both earbuds for about 3 seconds, lights will illuminate for 1 second to show the earbuds are powered on.
* Protective film must be removed from earbuds before they can be powered on and paired
Power on the left and right earbuds as described in the "Power On" portion of this guide.
Find and select "KOSS TWS150i" in the Bluetooth list.
NOTE:
Problem: If Bluetooth on source device is turned off, the earbuds will automatically turn off after 10 minutes. If earbuds are disconnected, the L/R earbuds' red and white lights will flash alternately.
Solution: Make sure that the source device's Bluetooth is turned on; then power on earbuds again.
Problem: If the connection between the device and the earbuds exceeds the effective range, the earbuds will power off automatically after 10 minutes.
Solution: Make sure that device is in range, then power on earbuds.
Double-tap on the L/R touch strip.
Double-tap on the L/R touch strip.
Long hold the L/R touch strip for 2 seconds.
Double tap the L/R earbud touch strip to pause/play music in standby or music mode.
While paused: Indicator lights illuminate once every 5 seconds
While playing: Indicator lights illuminate once every 5 seconds
Hold the right earbud touch strip for 2s
Note: This function is not supported when L earbuds are used alone.
Hold the left earbud touch strip for 2s
Place the earbuds into the charging case and closed the lid to automatically power down earbuds.
Place the earbuds in the charging case.
Charging: The left and right lights of the charging case will flash
Fully charged: No charging case lights are illuminated
The L side charging case light slowly flashes when the L earbud is charging.
The R side charging case light slowly flashes when the R earbud is charging.
When L and R earbuds are charged at the same time, the L and R charging case lights slowly flash at the same time.
When the earbud's batteries are full, the charging case lights will indicate the battery power level for 5 seconds.
When the power is below 30%, the left light flashes.
When the power is 30%~60%, the left light is always on and the center light flashes.
When the power is greater than 60%, the left and center lights are always on and the right light flashes.
When the power is 100%, all 3 lights remain on.
When the power is below 10%, the left light flashes.
When the power is 10%~30%, the left light is on.
When the power is 30%~60%, the left and center lights are on.
When power is 70%~100%, all 3 lights remain on.
Using earbuds at high volumes for extended periods of time may result in permanent hearing damage. It is advised you keep volume levels moderate to low at all times for your safety.
Do not use while driving a car, cycling, operating machinery, or performing other activities that require hearing surrounding sounds.
Earbuds may not work properly under high temperature or high humidity conditions.
Do not use any corrosive cleaner/oil to clean the earbuds.
If the earbuds come in contact with liquids, quickly wipe away. If submerged in water, do not turn the earbuds on until completely dried.
Tips: liquid submersion voids the warranty.
Keep the earbuds and packaging out of reach of children.
Battery warning!
Lithium ion Battery:
Model: 702334, 3.7V, 500mAh
GOLDEN CEL BATTERY CO. LTD.
Yinhu Industrial Park, Jiaoyitang Management Zone
Tngxia Town, Dongguan City, Guangzhou Province
Use this product in an environment with a temperature between 0℃ and 45℃; otherwise, it may damage your headset.
Bluetooth Earbuds Model: KOSS TWS250i
DC input: 5V380mA
Battery Capacity: 500mAh, 1.85Wh
Koss Corporation Made in China
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Need help?
Do you have a question about the TWS150i and is the answer not in the manual?
Questions and answers