Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for V7 CHGCT30i
- Page 1 UV-C Cleanse and Sanitizer Kit for V7 CHGCT30i & CHGCT36i Charge Carts...
- Page 2 TABLE OF CONTENTS SAFETY AND WARNINGS Safety and warnings FUNCTIONS Functions PACKAGE INCLUDES Package Includes INSTALLATION Installation...
- Page 3 SAFETY AND WARNINGS CAUTION Check www.v7world.com This symbol on the product indicates important for additional support and literature concerning operation and maintenance. Do not remove or alter labels. installation information. • This product uses UV-C light. Warning: eye and skin damage may result from direct exposure to the light produced by these lamps.
- Page 4 FUNCTIONS FRONT REAR Charge Cart's UV-C Kit is a set of 3 UV-C led bars, a specific control board and accessories. Charge Cart’s UV-C kit uses UV technology to disinfect the devices stored in the Cart. It automatically starts the disinfection process after 30 seconds from the closure of the doors. To safely use the UVC LEDs kit, the system requires to always close both doors completely: left door first and then right door, closing the handle.
- Page 5 Prevention to accidental exposure User must always close both doors when not operating the Charge Cart. Whenever the user opens the cart’s doors before the disinfection process is over, UV-C LEDs are instantly turned off in order to prevent any possible direct exposure. The process will restart with the 30 seconds countdown when closing doors.
- Page 6 PACKAGE INCLUDES UV-C LED (x3) UV-C BOARD TAMPER UV-C BOARD MAGNET BOX SUPPORT SAFETY TAMPER LABEL CABLE...
- Page 7 INSTALLATION CAUTION It is mandatory to apply the safety label provided in the box. Position the label as shown in the image below. Make sure to position the label centered. Ensure it is readable from the front side, where the user will load devices.
- Page 8 INSTALLATION To install UV-C kit, the user needs to remove each drawer. Pull the drawer completely out: this allows the user to can find levers to remove the drawer from the cart. Find levers at the side of the slide. LEVERS Once removed, UV-C LEDs can be installed.
- Page 9 Installation of the Tamper in the in the front door: - Place the nut in its support (behind the magnet) - Slide the magnet in the opening - Insert screws through the holes in the lateral part of the door and fix it Remove the frontplate with power led indicators by unscrewing the four screws (see circles in the figure 3).
- Page 10 Slide the metal part of the “tamper cable” underneath all cablings of the frontplate. Once in position, turn the frontplate upside-down and fix the tamper with screws. INSIDE OUTSIDE Move the tamper cable to the rear side of the cart. To do so, remove the frontplate on the rear part of the cart by unscrewing the four screws (see circles in figure 4).
- Page 11 Remove the rear frontplate and proceed with the installation of the UV-C box support. Position it facing the outside (1) and turn it upside-down, then attach it with screws (2). Position it facing the outside (1) Turn it upside-down, than attach it with screws (2) ATTENTION Make sure to install the UV-C Box support to the hole that will be positioned on the left when repositioning the frontplate.
- Page 12 Pass the “tamper cable” through the holes positioned in top-corners pushing it via the openings (highlighted below) so that the cable pin will be in the rear side of the cart. FRONT SIDE REAR SIDE Now assemble the frontplate back in its original position by plugging the connector and usign screws to fix it.
- Page 13 Installation of the UVC box: - Position UV-C box in the left part of the rear frontplate, paying attention to the cablings. Make sure to tie the tamper cable up and that the UV-C box flaps are positioned under the cable.
- Page 14 Once everything is correctly installed, the rear side of the cart is like this. Link the cable coming from UV-C LEDs to the box with this pattern: 1st row 2nd row 3rd row...
- Page 15 Model/Modelo/Modèle/Modell/Modello/Modelo: Date of purchase/ Fecha de compra/ Date d’achat/Kaufdatum/Data di acquisto/ Aankoop-datum/ Data de compra: Europe Australia Ingram Micro Inc. Ingram Micro Pan Europe GmbH Ingram Micro Pty Ltd 3351 Michelson Dr. Suite 100 Heisenbergbogen 3, 61 Dunning Ave, Rosebery Irvine, CA 92612, USA D-85609 Dornach / Munich, Germany NSW 2018, Australia...
- Page 16 RECOMMENDATIONS FOR DISPOSAL Correct disposal of the WEEE product (waste from electrical and electronic equipment) The symbol shown on the product, on the accessories and on the documentation (Fig.1) indicates that the product and its electronic accessories (such as cables, adapters, electrical parts in general) must not be disposed of with other unsorted waste at the end of their life cycle. To avoid any damage to the environment, the user is invited to separate the product and the aforementioned accessories from other types of waste.
- Page 17 www.v7world.com...
- Page 18 THIS PAGE WAS INTENTIONALLY LEFT BLANK...
- Page 19 THIS PAGE WAS INTENTIONALLY LEFT BLANK...
- Page 20 THIS PAGE WAS INTENTIONALLY LEFT BLANK...
Need help?
Do you have a question about the CHGCT30i and is the answer not in the manual?
Questions and answers