Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Connect Systems CS-700
Summary of Contents for Connect Systems CS-700
- Page 1 1802 Eastman Ave. Suite 116 Ventura, Ca. 93003 Phone (805) 642-7184 Fax (805) 642-7271 Model CS-700 VOX Enhanced VOX Controlled Sampling Interconnect USER'S INSTRUCTION MANUAL Made in U.S.A. Copyright (C) 1990 By Connect Systems Inc. Connect Systems Inc. - Model CS-700...
-
Page 2: Table Of Contents
The CS-700 is the only interconnect available that gives the user a choice of VOX Enhanced or VOX Controlled Sampling. Each choice offers distinctly unique advantages. -
Page 3: Installation And Adjustments
INSTALLATION AND ADJUSTMENTS The CS-700 requires only three connections to most radios. Use shielded wires with the shields at each end connected to chassis ground. (The rear panel barrier strip terminals labelled "GND" are chassis ground). We recommend using spade type crimp-on connectors for ease and reliability. -
Page 4: Programming The Cs-700
JP-1 Audio output range strap. Strap in = (0-1V), out = (0-5V). PROGRAMMING THE CS-700 The CS-700 has three easy-access programming areas: Operating Parameters, CW ID and Auto-Dial Phone Numbers. To enter one of the programming areas, turn the power off, press and hold the corresponding programming area button (No. -
Page 5: Operating Mode And Parameters
0.2. while the telephone party is talking. This allows the mobile to maintain full control. VOX Controlled Sampling: Sampling stops completely while the land party is speaking. In fact, sampling will never be heard if the Connect Systems Inc. - Model CS-700 Page... - Page 6 The sample width may be set manually or with the built-in automatic set-up feature. The sample width can only be adjusted if the CS-700 is properly connected to your radio, and the noise light is illuminated.
- Page 7 Such as access code = *56 and secret code = *3927. NOTE: The secret Toll Override Code is inoperable if * up is selected on 0.6. At least one additional digit must be programmed. Connect Systems Inc. - Model CS-700 Page...
- Page 8 0 = Pulse DEFAULT: 1 = Tone Choose how the CS-700 will dial your phone calls. Select tone if you are in a touchtone telephone exchange, because dialing is much faster. Note that the CS-700 has fully regenerated touchtone unlike most other products available.
-
Page 9: 1.9. Cw Id
2.0. Automatic Busy Signal Disconnect 1 = Enable 0 = Disable DEFAULT: 1 = Enable 2.1. Automatic Dialtone Disconnect 1 = Enable 0 = Disable DEFAULT: 1 = Enable See page 16 for details about auto-busy/dialtone disconnect. Connect Systems Inc. - Model CS-700 Page... - Page 10 1 = Enable 0 = Disable DEFAULT: 0 = Disable Determines whether the CS-700 will ringout or auto-answer if the channel is busy (Enter 0). Or only when the channel is clear (Enter 2.5. Ringout on Ring Number 0 = Disable [2.8.]...
- Page 11 If desired, you can return to a previously programmed character position by holding down 'C' for several seconds. This will return you to A.A. Now enter the character position (line number) you wish to return to and press 'P'. Connect Systems Inc. - Model CS-700 Page...
-
Page 12: Autodialer
PROGRAMMING THE CALLSIGN The CW ID message (usually the station callsign) sent from the CS-700 may consist of up to 15 characters. To program the message, enter the desired character codes (from Table 1) starting at character position 0.1. through the length of the string. If the message is less than 15 characters, it must be terminated with code 38 (Message End). - Page 13 Now enter the autodial location you wish to return to and press 'P'. Returning to Operate To return to normal operation, switch off the power and then back on. You can now use your newly programmed autodial numbers! Connect Systems Inc. - Model CS-700 Page...
-
Page 14: Operation
LINE IN USE DETECTION: If line in use detection has been enabled, (0.5.), the CS-700 checks to see if the line is in use when a mobile attempts access. If the line is free the mobile will hear dialtone and he can proceed with his call. - Page 15 (0.6.) with 0. Similar to using the autodialer. e.g. 0*, 0*391 etc. HOOK FLASH: The CS-700 has built-in hook flash logic to operate certain phone company provided features such as call waiting. To flash, simply press * three times (***).
-
Page 16: Receiving Incoming Calls
Ringout is how the CS-700 alerts you to the presence of an incoming call. When a call comes in, the CS-700 first checks to see if the channel is in use (2.4.). The incoming rings are counted (2.5.) before a mobile alert is sent. -
Page 17: Auxiliary Relay
MIC is off-hook. Enter 0 (Connect) on line 2.2. This will energize the relay whenever the CS-700 is in use. Connect the normally closed contacts (W and NC) in series with the radios' hook switch. -
Page 18: Telephone Coupler
You must notify the phone company when discontinuing use. Also, connection to coin or party lines is prohibited. Installation: Remove the CS-700 PC board and solder the six position terminal block to the PC board. Connect the six leads per illustration below. -
Page 19: Warranty
LIMITED WARRANTY We guarantee the Model CS-700 to be free from defects in material and workmanship for one year from purchase. Tampering, misuse or modification shall void this agreement. Several components in the CS-700 are mounted in sockets. We reserve the right to not cover these parts under warranty if failure is traceable to removal/re-insertion. -
Page 20: Schematic Diagrams
Connect Systems Inc. - Model CS-700 Page... - Page 21 Connect Systems Inc. - Model CS-700 Page...
Need help?
Do you have a question about the CS-700 and is the answer not in the manual?
Questions and answers