Subscribe to Our Youtube Channel
Related Manuals for Titan Attachments SKID STEER TRUSS BOOM v3
Summary of Contents for Titan Attachments SKID STEER TRUSS BOOM v3
- Page 1 SKID STEER TRUSS BOOM v3 SSTRUSSBOOMv3 194153 Operator’s Manual Read the Operator’s Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious follow without exception. Your life and the lives of others depend on it!
- Page 2 INTRODUCTION • This manual is made at the time of manufacturing of the TRUSSBOOM that does not include any subsequent modifications made afterward. • This manual is intended to provide information to operators and owners to operate the TRUSSBOOM safely and effectively, as well as to perform suitable maintenance for the equipment.
- Page 3 PARTS DIAGRAM / EXPLODED VIEW DESCRIPTION SAFETY VALVE OIL HOSE - FEED FLAT FACE COUPLER - MALE FLAT FACE COUPLER - FEMALE GREASE ZERK EYE PIN FLAT WASHER M12 SPRING WASHER M12 HEX BOLT M12x30 (10) MAIN FRAME (11) HEX BOLT M20x60 (12) FLAT WASHER M20 (13)
-
Page 4: Specification
(15) TITAN ATTACHMENT DECAL (16) FLAT WASHER M10 (17) SPRING WASHER M10 (18) HEX NUT M10 (19) HEX BOLT M16x110 (20) HEX LOCK NUT M16 (21) TELEBOOM-1 (FIRST SECTION) (22) HEX BOLT M10x50 (23) SLIDE ROLLER (24) TELEBOOM-2 (SECOND SECTION) (25) HEX BOLT M16x100 (26) - Page 5 ASSEMBLY INSTRUCTIONS 1. REMOVE PARTS FROM STEEL CRATE The fork blade used to lift the steel crate should be at least 2/3 of the length of the crate. It is recommended that the left and right fork blades should move to the farthest ends. Failure to do so may lead to imbalance causing the crate to slide out that may cause injury.
- Page 6 2. PUTTING TOGETHER TELEBOOM ASSEMBLY • Place TELEBOOM-1/TELEBOOM-2 Assembly on a table. Insert TELEBOOM-3 (32) into TELEBOOM-2 (24). • Align holes of TELEBOOM-2 (24) to the farthest holes of TELEBOOM-3 (32) and insert LOCK PIN (29) through these holes to lock the TELEBOOM Assembly together.
- Page 7 3. ATTACHING MAIN FRAME TO THE TELEBOOM ASSEMBLY • Move skid steer loader that picks up the MAIN FRAME (10) to the table where the TELEBOOM Assembly is placed. • The hardware sets that are used to mount the Main Frame onto the Teleboom Assembly are attached to the main frame for transportation.
- Page 8 4. MOUNTING CYLINDER • Align holes of CYLINDER (31) with the mount tabs on MAIN FRAME (10) and insert CYLINDER PIN (27) Into these holes. • Insert EYE PIN (6) into the holes of CYLINDER PIN (27) and secure the EYE PIN (6) onto MAIN FRAME (10) using HEX BOLT M12x30 (9), FLAT WASHER M12 (7) and SPRING WASHER M12 (8).
-
Page 9: Hydraulic System
HYDRAULIC SYSTEM DESCRIPTION (31) HYDRAULIC CYLINDER SAFETY VALVE (35) GASKET Ø3/8” (34) HOSE CONNECTOR G3/8” OIL HOSE - FEED FLAT FACE COUPLER - MALE FLAT FACE COUPLER -FEMALE (33) OIL HOSE - RETURN SAFETY VALVE • Titan TRUSSBOOM is equipped with safety valve that serves to regulate hydraulic oil flows so that in the event of hydraulic failure, the boom will not collapse instantly causing hazard. - Page 10 ACKNOWLEDGEMENT OF RISK AND RELEASE OF LIABILITY The use of any equipment, including this one, involves the potential risk of injury. Apart from any warranty claim that might be presented for a claimed defect in material or workmanship of the product, you accept and assume full responsibility for any and all injuries, damages (both economic and non- economic), and losses of any type, which may occur, and you fully and forever release and discharge Titan, its insurers, employees, officers, directors, associates, and agents from any and all claims,...
- Page 11 NEED HELP? CONTACT US FIRST. 1-800-605-7595 info@palletworks.com www.palletforks.com © 2023 Titan Brands...
Need help?
Do you have a question about the SKID STEER TRUSS BOOM v3 and is the answer not in the manual?
Questions and answers