Advertisement
Quick Links
Advertisement
Related Manuals for Transystem PLC100
Summary of Contents for Transystem PLC100
- Page 2 Transmitter Operation Manual Copyright 2007, YSTEM All rights reserved TRANSYSTEM INC. No.1-2 Li-Hsin Rd.I Science-Based Industrial Park, Hsinchu, Taiwan Tel:+886-3-5780393 Fax:+886-3-5784111 e-mail: sales@transystem.com.tw website: www.transystem.com.tw 8029607101A...
- Page 3 *Contact Us: The Headquarter Tel : + 886-3-578-0393 Fax: + 886-3-578-4111 Website: http://www.transystem.com.tw E-mail: sales@transystem.com.tw Address: NO. 1-2, LI-HSIN RD.I, SCIENCE-BASED INDUSTRIAL PARK, HSINCHU, TAIWAN...
-
Page 4: Table Of Contents
TABLE OF CONTENTS Chapter 1. General Information 1.1 Module Features and Specifications Chapter 2. Installation 2.1 Step by Step Installation 2.2 Connection to the Power Inserter and Cable Modem 2.3 Waterproofing Connections Chapter 3. Accessories 3.1 MMDS Antenna... -
Page 5: Chapter 1. General Information
Chapter 1. General Information 1.1 Module Features and Specifications PLC100 PLC200 Input Frequency 22~34 MHz 12~42 MHz Output Frequency 2170~2182MHz 2500~2530MHz Output 1 dB 24dBm Typ. 24dBm Typ. Compression Point Output 24±2dB 24±2dB Transmitting Gain -122dBm/Hz Max -116dBm/Hz Max Output... -
Page 6: Chapter 2. Installation
Chapter 2. Installation 2.1 Step by Step Installation 2.1.1 Mounting Bracket Assembly Suite The following hardwares are suggested for mounting the Transmitter to the pole. A set of mounting bracket includes ONE 2511 mounting bracket, ONE bracket 3, ONE bracket 2, TWO screws 4013, and FOUR hex flange nuts. - Page 7 2.1.2 Step by Step Installation Step 1 – Attach sequence Left to right: Bracket 3, Bracket 2, and 2511 Mounting Bracket. Step 2 – How to Attach The concave of Bracket 2 is for holding onto the pole.
- Page 8 Step 3 – Tighten the bracket against pole Step 4 – Installation Complete Loosen Screws A & B for left-and-right and up-and-down angle adjustments. Tighten up Screws A & B after fixing the directions.
-
Page 9: Connection To The Power Inserter And Cable Modem
2.2 Connection to the Power Inserter and Cable Modem Connections to the Transmitter are shown in diagram 2.2. Please note: ① The power inserter normally has 3 ports: Connect to wall adapter with RG-59 cable ANT Connect to the Transmitter Connect to Cable modem VERY IMPORTANT NOTICE! a. - Page 10 ② After connection, the F connector of Transmitter must be sealed with an asphalt sealing tape. (For details, please refer to Section 2.3 Waterproofing Connections) Diagram 2.2: Connection to Cable modem & Power Inserter...
-
Page 11: Waterproofing Connections
2.3 Waterproofing Connections Water-proofing is very important during installation of Transmitter. Please use the included water-proof asphalt tape to seal off the F-connector as shown below: ① After you plug in the coaxial cable into the F-connector, use the included water-proofing asphalt tape to seal off the F-connector from the bottom (i.e. the part close to Transmitter). - Page 12 ③ The total width of the wrap-around is about 6cm, which corresponds to 7 to 8 rounds of tapes. * Warning: If you do not follow the above procedure, the Transmitter could become malfunctioning due to water leakage.
-
Page 13: Chapter 3 Accessories
Chapter 3 Accessories 3.1 MMDS Antenna TSI is proud to offer a complete line of 2.5GHz antennas specifically designed to satisfy your subscribers. Below are the series: 12dBi Corner Reflector 15dBi Spotbeam 17 dBi Viper Parabolic Mesh Antenna (18, 21, 24dBi)
Need help?
Do you have a question about the PLC100 and is the answer not in the manual?
Questions and answers