Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Benchmark 1280-002
Summary of Contents for Benchmark 1280-002
- Page 1 OSCILLATING MULTI-TOOL KIT 5 year limited warranty on tool READ ALL INSTRUCTIONS BEFORE FIRST USE. KEEP THIS MANUAL FOR FUTURE REFERENCE. KEEP AWAY FROM CHILDREN. 3042597 JD2480UH WEAR CSA APPROVED WEAR EAR WEAR A EYE PROTECTION PROTECTION FACE MASK...
-
Page 2: Product Specifications
PRODUCT SPECIFICATIONS OSCILLATING MULTI-TOOL KIT Rating 120 V, 60 Hz AC Amperes Variable speed 11,000–21,000 OPM (no load) Oscillating angle 3.2° Weight 5 lb 2 oz (2.3 kg) NEED ASSISTANCE? Call us on our toll- free customer support line: 1-866-349-8665 (Monday through Friday 9am – 5pm Eastern Standard Time) •... -
Page 3: Table Of Contents
1280-002 OSCILLATING MULTI-TOOL KIT TABLE OF CONTENTS Product Specifications ................... 1 Table of Contents ................... 2 General Safety Warnings ................3 Eye, Ear & Lung Protection ................3 Power Tool Safety ................... 3 General Safety Rules ..................3 Electrical Safety and Extension Cord Guidelines ..........4 Work Area Safety ................... -
Page 4: General Safety Warnings
GENERAL SAFETY WARNINGS WARNING: Before using this tool or any of its accessories, read this manual and follow all Safety Rules and Operating Instructions. The important precautions, safeguards and instructions appearing in this manual are not meant to cover all possible situations. -
Page 5: Electrical Safety And Extension Cord Guidelines
1280-002 OSCILLATING MULTI-TOOL KIT VOLTS Total Length of Cord in Feet (meters) 120V 25' (7.5 m) 50' (15 m) 100' (30 m) 150' (45m) 240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4) Amperage rate American Wire Gauge More than... -
Page 6: Personal Safety
PERSONAL SAFETY • Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. -
Page 7: Service
1280-002 OSCILLATING MULTI-TOOL KIT could result in a hazardous situation. • Hold power tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. -
Page 8: Symbols
SYMBOLS WARNING: Some of the following symbols may appear on the oscillating tool. Study these symbols and learn their meaning. Proper interpretation of these Three-phase alternating Volts current with neutral Amperes Read all documentation Hertz Direct current Watts No load speed Kilowatts Alternating or direct current Microfarads... -
Page 9: Know Your Oscillating Tool
1280-002 OSCILLATING MULTI-TOOL KIT KNOW YOUR OSCILLATING 3A TOOL Speed control Tool less accessory ON/OFF wheel holder release lever switch Air vents LED Work light Open back accessory holder ACCESSORIES OSCILLATING TOOL COMPONENTS KEY DESCRIPTION 1-3/4" bi metal plunge blade 2”... -
Page 10: Assembly And Operating
ASSEMBLY AND OPERATING NOTE: The drawings in the assembly and operating section of this manual may INSTALLING ACCESSORIES All accessories are installed on this oscillating tool in a similar manner. For the purposes of describing the accessory installation, the triangular sanding pad and the metal cutting blade have been illustrated. -
Page 11: Installing Sandpaper
1280-002 OSCILLATING MULTI-TOOL KIT INSTALLING SANDPAPER 1. Install the hook & loop sanding pad (1) onto the tool (Fig. 2). 2. Firmly press the sandpaper (2) onto the hook & loop pad. NOTE: Press the sandpaper firmly onto the hook & loop pad. -
Page 12: Speed Control Wheel
Fig. 6 SPEED CONTROL WHEEL The speed of the tool can be adjusted to run the tool at speeds varying between 11,000 OPM and 21,000 OPM by rotating the speed control wheel (1) located toward the rear of the tool housing (Fig. 8). 1. -
Page 13: Flush Cutting A Door Jamb And Casing For Installing Flooring
1280-002 OSCILLATING MULTI-TOOL KIT WARNING: For safety reasons, the operator must read the sections of this Owner’s Manual entitled “GENERAL SAFETY WARNINGS”, “POWER TOOL SAFETY”, “SPECIFIC SAFETY RULES” and “ before using this oscillating tool. Verify the following every time the oscillating tool is used: 1. -
Page 14: Cutting A Hole In Wood Flooring To Install A Heating Vent
6. When the tool reaches its maximum set speed, carefully plunge the blade into the door jamb while sliding the blade along the floor tile. NOTE: Hold the tool tightly and do not put too much forward pressure on the saw blade when cutting, as this will cause the tool to vibrate excessively. -
Page 15: Cutting A Hole In Drywall For Installing An Electrical Outlet Box
1280-002 OSCILLATING MULTI-TOOL KIT Fig. 8 Fig. 9 INSTALLING AN ELECTRICAL OUTLET BOX The oscillating tool can be used to cut a hole in drywall for installing an electrical outlet box. 1. Install the half circle saw blade for wood & drywall in the tool. -
Page 16: Using The Detail Sander Attachment
7. Turn the saw OFF, remove it from the cut and proceed to cut in the opposite direction to complete the cut for the first side of the rectangle. 8. Repeat steps #4, #5 & #6 to cut the remaining three sides of the rectangle. 9. -
Page 17: Maintenance
1280-002 OSCILLATING MULTI-TOOL KIT MAINTENANCE GENERAL WARNING: When servicing, use only identical replacement parts. The use of any other part may create a hazard or cause product damage. DO NOT use solvents when cleaning plastic parts. Plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. - Page 18 NOTE: The two screws at the rear of the handle (3) are shorter than the other three. These must be replaced in the same position when replacing the handle screws. NOTE: Make sure you note the positioning of the speed control wheel and all the wires.
- Page 19 1280-002 OSCILLATING MULTI-TOOL KIT b) Do NOT replace the handle screws until the second motor brush has been replaced. 11. Grasp the reassembled handle and turn the tool onto its right side and remove the left half of the handle.
-
Page 20: Exploded View
EXPLODED VIEW... -
Page 21: Parts List
1280-002 OSCILLATING MULTI-TOOL KIT PARTS LIST WARNING: When servicing, use only original equipment replacement parts. The use of any other parts may create a safety hazard or cause damage to the tool. Any attempt to repair or replace electrical parts on this tool may create a safety hazard unless repairs are performed by a qualified technician. - Page 22 Key# Part # Part Name 4010010022 Ball bearing 6900-2Z 4100010007 Circlip 22 4010010146 Ball bearing 6804Z 4100010005 Circlip 32 2040290093 Output shaft 3120010106 Button for ON/OFF switch 3120110066 Switch actuating lever 3011210008 Motor housing 2030070015 Brush holder support 4030010136 Screw ST2.9x9 1230010075 Brush 2050020025...
-
Page 23: Warranty
WARRANTY BENCHMARK OSCILLATING MULTI-TOOL KIT WARRANTY If this Benchmark tool fails due to a defect in material or workmanship within five years from the date of purchase, return it to any Home Hardware store with the original bill of sale for exchange. 3-year warranty for the battery and charger. This warranty does not include expendable parts including but not limited to blades, brushes, belts, light bulbs. - Page 25 1280-002 OSCILLATING MULTI-TOOL KIT...
- Page 26 OSCILLATING MULTI-TOOL KIT 5 year limited warranty on tool 1280-002 BENCHMARK TOOLS CANADA Made in China ST. JACOBS, ONTARIO N0B 2N0 © 01 / 2021 Home Hardware Stores Limited CUSTOMER SERVICE/TECH SUPPORT 1-866-349-8665 * This Benchmark product carries a five (5) year LIMITED warranty against defects in workmanship and materials.
Need help?
Do you have a question about the 1280-002 and is the answer not in the manual?
Questions and answers