Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Shift SKYTAB
- Page 1 SkyTab POS Installation Guide SkyTab Support: (888) 647-8603...
-
Page 2: Table Of Contents
Barcode Scanner 2D Barcode Scanner Dot Matrix Kitchen Printer Caller ID Kitchen Display System (KDS) Wireless Accessory Installation TP-Link Archer Router SkyTab Mobile SkyTab Glass Equipment Mounting Mounting SkyTab POS Mounting SkyTab KDS Deactivating Demo Employees SkyTab Support: (888) 647-8603... -
Page 3: Prior To Installation
• Single LAN Port Modem – This modem only allows one router to be connected directly to it and other routers may have to be hooked up to each other. Cat 5e Merchant Equipment Cat 5e Cat 5e Modem/Router TP-Link Router SkyTab Equipment Archer - only if ST Glass is used SkyTab Support: (888) 647-8603... -
Page 4: Cash Drawer
2. Connect a CAT5 Ethernet cable to the WAN port on the router and the other end to the merchant’s modem. • If the merchant is using SkyTab Glass the Archer router should be installed in a location that requires adequate coverage for the devices. -
Page 5: Receipt Printer
SYSTEM INSTALLATION RECEIPT PRINTER Connecting the Printer The Epson TM-m30 receipt printer receives power and data from the SkyTab POS Hub via USB and power from a nearby wall outlet. Loading the Paper 1. Place the thermal paper roll into the top of the receipt printer, feeding from underneath the roll. -
Page 6: Skytab Pos
SYSTEM INSTALLATION SKYTAB POS The Onyx POS system is comprised of three components: 1. The SkyTab multipurpose hub. 2. The SkyTab POS Workstation. 3. The power adapter and cable. The Multipurpose hub is connected via USB-C to 1 of 2 ports on the bottom of the POS. -
Page 7: Credit Card Pin Pads
The Epson TM-m30 printer uses DHCP to assign a dynamic IP address. 1. Connect the Ethernet cable to the remote printer and then to the SkyTab POS network. 2. Connect the power supply to the remote printer. Connect the power cable first to the power supply and then to a power port. -
Page 8: Scale (Optional)
• Lock the weight-added iron patch 2. Plug the USB cable into the POS system. 2D BARCODE SCANNER 1. Plug the USB cable into the POS system. NOTE: A stand is not included or offered with the 2D barcode scanner. SkyTab Support: (888) 647-8603... -
Page 9: Dot Matrix Kitchen Printer
3. Press “Feed” to advance the paper. Loading the Ribbon 1. Open the front tray of the printer. 2. Place the plastic edge in first, angling the ribbon upwards. 3. Push down until the cartridge clicks in place. SkyTab Support: (888) 647-8603... -
Page 10: Caller Id
(800) 444-4444 which is an automatic number announcement circuit. This will tell you the phone number that you are currently calling from. 111-222-4444 Duplicator Phone Cable Phone Cable SkyTab Support: (888) 647-8603... -
Page 11: Kitchen Display System (Kds)
KITCHEN DISPLAY SYSTEM (KDS) SkyTab KDS is an all-in-one touch screen unit. It does not have a control box or bump bar like other standard kitchen display systems. It also does not ship with a stand attached, but a vesa base is included that must be attached to the KDS. -
Page 12: Skytab Glass
• Turn on by pressing the power button on the right side of the tablet. • SkyTab Glass should already be configured to the Archer router’s wireless network. If not, be sure to obtain the SSID and Password from your support contact to connect the device to the wireless network. -
Page 13: Equipment Mounting
• Shift4 does not support the installation of mounts for any of the equipment we provide. • If the merchant has a mount installed prior to the POS installation, we can attach the SkyTab POS or KDS to the mount during installation. -
Page 14: Deactivating Demo Employees
• To accomplish this navigate to Manager > Settings > Users > Employees. • Highlight the demo employee. • Tap on the toggle up top next to active. • Tap on Save. • Repeat for each demo employee. © 2022 Shift4. All rights reserved. ST1102_11114022_SK SkyTab Support: (888) 647-8603...
Need help?
Do you have a question about the SKYTAB and is the answer not in the manual?
Questions and answers