Summary of Contents for VER-MAC Speed-Mac VP
- Page 1 Portable Speed Sensor Speed-Mac VP Operation, Safety and Maintenance Manual Document number MAN-118...
-
Page 2: Table Of Contents
Overview ..........................1 Unpacking and First Setup ....................2 Operation ..........................5 Setting Up in the Work Zone ..................5 Turning the Speed-Mac VP ON or OFF ................. 5 Troubleshooting ......................... 6 LEDs ..........................6 Low Batteries ........................ 6 Battery Recharging Process ..................7 Long-Term Storage and Battery Safety Information ............ - Page 3 Follow us https://www.facebook.com/VermacInc https://www.linkedin.com/company/ver-mac Technical Support For help with any difficulties concerning Speed-Mac VP units or this manual, please contact Ver- Mac Support: support@ver-mac.com mysupport.ver-mac.com Disclaimer Failure to read and follow the instructions and procedures contained in this manual could result in failure of the equipment, damage and, serious injury.
-
Page 4: Overview
VP addition. It can be easily set up by one man and will operate all seasons without recharging, in most applications. The Speed-Mac VP is the only autonomous NCHRP 350 tested and approved device on the market. Our Speed-Mac 2.0 is a portable sensor system packaged inside a standard barricade light. -
Page 5: Unpacking And First Setup
1. Make sure you have the lock and other parts that were shipped initially in the casing. Remove the electrical tape Connect with this wire 2. Make sure the cables fit inside and close the casing: Ver-Mac 2020 Operation, Safety and Maintenance Manual v3.0... - Page 6 Unpacking and First Setup 3. Fold the vertical panel: 4. Place a foot on one leg, bring up the panel and bring down the second leg. 5. Connect and install the Speed-Mac 2.0: Ver-Mac 2020 Operation, Safety and Maintenance Manual v3.0...
- Page 7 The solar panel will charge the batteries; you should be able to leave it operate for long periods of time. Make sure to disconnect the batteries from the Speed-Mac VP units when NOTE taking down the work zone (see step 1).
-
Page 8: Operation
3.1 Setting Up in the Work Zone For your Speed-Mac VP units to operate accurately the whole duration of the work zone, you need to follow this procedure: 1. Set-up the Speed-Mac 2.0 unit on its panel, according to chapter 2. -
Page 9: Troubleshooting
If battery level is low, you will need to make sure the solar panel is charging it. Make sure the solar panel it is facing south (see 3.1). Make sure it is clean and undamaged. DO NOT charge using a car battery. Ver-Mac 2020 Operation, Safety and Maintenance Manual v3.0... -
Page 10: Battery Recharging Process
Long-Term Storage and Battery Safety Information 4.3 Battery Recharging Process The Speed-Mac VP has an internal battery and an on-board charger. If you want to recharge the battery, perform one of the following while the unit is OFF: Connect the unit on the solar vertical panel (VP), put it outside with the panel facing south. The unit will self-recharge within a few days. -
Page 11: Information About The Gps
GPS: global positioning by satellite. RH: relative humidity. Speed-Mac VP: Includes the Speed-Mac 2.0 and the exclusive vertical barricade with integrated solar panel. Speed-Mac 2.0: The head and its yellow base only, for customers who wish to install it on a different system. - Page 12 Signalisation Ver-Mac and shall be carried out at its factory, unless otherwise agreed by prior arrangement with Signalisation Ver-Mac. • Signalisation Ver-Mac shall not be held liable for any cost incurred by the owner in the execution of repairs.
- Page 13 • Defective equipment or component parts for repair or replacement must always be returned to Signalisation Ver-Mac Inc. along with an RMA number obtained beforehand from Customer Service at Signalisation Ver-Mac Inc.
Need help?
Do you have a question about the Speed-Mac VP and is the answer not in the manual?
Questions and answers