Pioneer KEH-M5500 UC Service Manual page 4

(2] Eject
[3] Cassette Door
{12] Source Selector
{18] Loudness
[19] Display
[20] Volume/Balance
{21] Fader
Switching Power On
Tape
+ GEH-M2000 does not include this tape
deck function.
Insert the cassette tape through the
Cassette Door [3], and the power will be au-
tomatically turned on to get the tape start
being played back. To eject the tape, press
the button [2].
Radio, Multi-play CD player
The unit incorporates priority cassette tape
play. The unit will not switch to radio or
multi-play CD player while a tape is insert-
ed. Press button [2] to eject the tape.
+ GEH-M2000 does not include tape deck
function. Therefore, procedures men-
tioned above will not be necessary.
Press button [12] to switch the radio on.
Multi-play CD player — Radio — OFF.
Parts Identification
(Fig. 1)
[4] Preset
6] Band
{12] Source Selector
13] Best Stations Memory (BSM)
{15] Local Station
[16] Preset Scan
17] FM Stereo/Mono
[19] Display
(Fig. 2)
22} Local Station
[23] Seek
{24] Preset Scan
26] Preset Number
27] FM Mono
{28] FM Stereo
[29] Frequency
30] Band
Listening to the Radio
+ Electronic Tuner
Frequency allocation differs depending
upon the area. This unit has been designed
in accordance with the frequency alloca-
tions for North America. Use in other areas
will result in improper reception.
Adjusting Audio
Adjusting Volume
Turn the control [20] to the right to raise the
volume. Turn the control to the left to lower
the volume.
Adjusting the Fader
Turn the control [21] upward to fade sound
in the rear speakers. Turn the control down-
wards to fade sound in the front speakers.
+ With a 2 speaker system, set the contro!
in a central position.
Adjusting Bass
Turn the control [1] to the right to increase
bass. Turn the control to the left to de-
crease bass.
Adjusting Treble
Pull the control [1] towards you until it
clicks. Turn the contro! to the right while it
is in this position to increase treble. Turn it
to the left to decrease treble. After adjusting
the control, push it back to its original posi-
tion.
Adjusting Balance
Pull the control [20] towards you until it
clicks. Turn the control to the right while it
is in this position to fade sound in the left
speaker. Turn it to the left to fade sound in
the right speaker. After adjusting the con-
trol, push it back to its original position.
Using the Loudness Function
Press button [18] and the "LOUD" indicator
will appear on the display. This "loudness"
function enhances both the high and low
ranges of sound to give even more power
to output even at low volumes.
KEH-M5500, KEH-M4500
The unit incorporates priority cassette tape
play. The unit will not switch to radio play
while a tape is inserted, so be sure to eject
the tape when you wish to listen to the ra-
dio.
1.Press button [12] to switch the radio
power on.
Press button [12] to switch the tuner on and
off. Oprerations will be different when the
unit is combined with a seperately available
multi-play CD player (CDX-M390, etc.). For
details on "Switching Power ON" refer to
the relevent clause, on page 4.
2.Press button [6] to select a band.
F -Fi-Fi-A
(FM1) (FM2) (FM3) (AM)
display.
BSM (Best Stations Memory)
This function automatically locates stronger
stations and automatically assigns their fre-
quencies to the buttons in Bank [4], from
strongest to weakest. It comes in handy
when trying to find local stations while driv-
ing.
1.Press button [6] and select a band.
2.Holding down button [13] for about two
seconds will start BSM search. At this
time, "BSM" will flash on the display.
3.The frequency display will return once
BSM search is complete, and frequencies
are assigned to buttons 1 through 6 in
Bank [4].
At the end of the BSM search, the dis-
played frequency is that assigned to but-
ton @) of Bank [41.
if there are fewer than six strong stations
in the area, some of the buttons in Bank
[4] will not be assigned frequencies, so
they will retain any frequencies assigned
to them previously.
BSM search may take as long as 30 sec-
onds in areas where there are few strong
stations.
You can cance! BSM search by pressing
button [13] again.