Renu Electronics FPEM-1210P-A0201L-V2 Quick Start Manual

FPEM-1210P-A0201L-V2
QUICK START GUIDE
12 Bi-directional type inputs, 10
FPEM-1210P-A0201L-V2:
PNP type transistor outputs. 2 Analog inputs (16-bit
resolution) & 1 Analog output (12-bit resolution)
For more information, please refer user manual which
will be available in FlexiSoft software help and/or you
can download from REPL website.
Dimension Details:
SPECIFICATIONS
Power Supply
Voltage Rating 24VDC (±15%), 12V from base
Input/channel: 24VDC, 5mA typical
Power Rating
Output/Channel: 250mA @ 24VDC
Optical Isolation for all I/O points. High
Isolation
isolation voltage (BV= Greater than
1.5kV)
Local I/O Specification
Number of Inputs 12 Inputs Bi-directional Type
ON Voltage Min.: 15VDC, Max.: 30VDC
OFF Voltage Min.: -3VDC, Max.: 3VDC
Nominal Input Voltage 24VDC
Nominal Input Current
5mA typical
Input Response Time ON: 10msec, OFF: 10msec
Input Impedance Greater than 4.8kΩ
High Speed Inputs 2 pairs, X0-X1, X2-X3
Max. I/P frequency 200kHz
Max. Input count 42949672965
Number of Outputs
10 PNP type transistor outputs
Nominal Output Voltage 24VDC
Nominal Output Current 250mA type/channel
Output Response Time ON/OFF: 20 to 30 µs
High Speed Outputs 2, Y0 and Y1
Max. O/P frequency 1kHz
Frequency step 1Hz
PWM duty cycle 0 to 100%
Duty cycle step 1%
Analog I/O Specification
Analog Input Total Channels 2 Input channels (16 bit resolution)
Input Type
0-20mA, 4-20mA & 0-10VDC, 0-5VDC
Analog Output Total Channels 1 Output channels (12 bit resolution)
Output type 0-20mA, 4-20mA and 0-10VDC, 0-5VDC
± 0.2% of full scale @ 25°C & ± 0.5% of
Accuracy
full scale over temperature range
Note:
In the Flexisoft select FPEM-1210P-A0201L
A0201L-V2 unit.
SPECIFICATIONS
Environment & Approvals
Operating Temperature**
Storage Temperature
Humidity
Product Dimensions
Approvals
**Operating temperature: For UL 0 to 50°C
Mounting with base models:
With the expansions, while unpacking the unit, user will
find two screws already attached with base bottom case.
Fix the expansion with the HMI as shown below with
these screws. Fix the Expansion connector with the
expansion female connector given on base HMI.
Apply torque 0.1Nm while fixing with base unit.
Mounting with 4.3" base model:
Mounting with 7" and 10.1" base model:
For 7" and 10.1" HMI models, the procedure of mounting
expansions is same. Only instead of horizontal mounting,
expansions will mount in vertical directions.
Hence, accordingly these bases are having facility to add
3 and 5 expansions at a time respectively.
Mounting with 7" base model:
Mounting with 10.1" base model:
or V2 for FPEM-1210P-
[Note: All Pictures shown are for illustration purpose
only. Actual product size may vary.]
0 to 60°C
-20 to 85°C
10 to 90% (Non-Condensing)
48mm x 108mm x 35.7mm (W x H x D)
CE, UL