1. Manuals
  2. Brands
  3. TAPRITE Manuals
  4. Beverage Dispenser
  5. Rattler II
  6. Instructional manual

TAPRITE Rattler II Instructional Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Instructional Manual
Rattler II Beverage Dispenser
Dispenser Model No. 950C
Please refer to the Taprite website (www.taprite.com) for information
relating to Taprite installation and Service
Manuals, Instruction Sheets, Technical Bulletins, Service Bulletins, etc.
The information contained in this document is subject to change without notice.
TAPRITE MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TAPRITE shall not be liable for
errors contained herein or for incidental consequential damages in connection with the finishings, performance, or
This document contains proprietary information which is protected by copyright. All rights reserved.
This manual must be read and understood before the installation and operation of this dispenser.
NOTICE:
use of this material.
© Copyright 2019 by Taprite, all rights reserved.
THIS DOCUMENT CONTAINS IMPORTANT INFORMATION
Taprite
3248 Northwestern Drive • San Antonio, TX 78238
Toll-Free 877.404.2488 • Fax: 210.646.6009 www.taprite.com
PN: 805-0039C
Rev: F
Released: 9/28/23
3158001

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Rattler II and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for TAPRITE Rattler II

  • Page 1 The information contained in this document is subject to change without notice. TAPRITE MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TAPRITE shall not be liable for errors contained herein or for incidental consequential damages in connection with the finishings, performance, or use of this material.

  • Page 2: Table Of Contents

    TABLE OF CONTENTS SUBJECT PAGE NUMBER Installation Setting Ratio Flow Control Cover Installation Butterfly Plate and Button Removal/Reassembly Removing and Replacing Stem O-Ring Cleaning and Maintenance Reattaching the Bar Gun Assembly Troubleshooting Line Configuration Juice and Energy Butterfly Plate Configurations 8 and 10 Butterfly Plate Configurations 12 and 14 Butterfly Plate Configurations 18-19...

  • Page 3: Installation

    INSTALLATION Thank you for purchasing a Taprite 950C bar dispenser. All required mounting hardware, holster assembly, and ¼” stainless-steel input fittings (with o-rings) are included with each bar dispenser. The stainless-steel input fittings are installed on the product side of the bar dispenser manifold (Fig.
  • Page 4 Fig. 2 B. Follow the labeling on the assembly to ensure proper product connection. C. Lock inlet line fittings into the valve module assembly before turning on syrup or water. To lock the fitting, lightly press down on the red clip. Lightly pull up on the clip to allow fitting removal.

  • Page 5: Setting Ratio

    F. Slide Flow Control Module/Mechanical Module (FCM/MM) onto base plate and verify that the two bosses on the plate are lined up. Secure the manifold to the base plate with the two thumb screws. G.To install the holster use the screws provided. Install the holster and drain assembly in close proximity to the bar gun location.
  • Page 6 G. Use a ratio cup to measure the syrup to water ratio. Adjust the flow controls to achieve the target ratio. INSTALLER TIP: The Taprite Bar Dispenser is equipped with a secondary water ratio screw that is located on the bottom of the bar dispenser handle near the nozzle (Fig.

  • Page 7: Flow Control Cover Installation

    CAPTIVE O-RING DESIGN (COR) Below are instructions for the latest revision of the Taprite bar dispenser handle. The Stem O-rings are located on top of the handle, under the button plate.

  • Page 8: Removing And Replacing Stem O-Ring

    REMOVING AND REPLACING STEM O-RING NOTE: The new retainer design allows one to service and replace the stem O-rings without the need to remove the bottom plate. The Stem O-rings are located on top of the handle, under the button plate. Begin by shutting off pressure.
  • Page 9 C. Remove O-Ring retainer by tilting the handle upside down, Fig.13. If retainer(s) does not fall out, carefully lift the clear retainer straight up by lightly applying outwards pressure with your fingers on the tabs of the retainer, see Fig. 14, and slowly guide up through the plunger stem(s).
  • Page 10 E. Insert the lubricated replacement O-ring, PN 208-5003, over the plunger stem and install into the bottom of the gland using the PN 316-0028 O-ring insert tool, Fig. Fig. 16 NOTE: Failure to shut off flow to the handle may result in a high-pressure blast of water or syrup to be shot out of the o-ring gland if plunger stem is accidentally depressed.

  • Page 11: Cleaning And Maintenance

    G. Assemble the butterfly plates and retainer, fasten to 2.5 inlb max. Do not over tighten IMPORTANT: Exceeding the max torque on the butterfly screws may impede proper function of the butterfly plate(s) and can strip threads on the handle. H.
  • Page 12 Daily Cleaning 1. Dispenser Handle a. Prepare sanitizing solution. b. Remove nozzle by twisting counterclockwise and pulling down and submerging nozzle into a sanitizing solution for 15 minutes. The diffuser is not removable. NOTE: Diffuser is removable, attempting to remove diffuser may damage dispenser c.

  • Page 13: Reattaching The Bar Gun Assembly

    6. Fill a bar sink or a 5 gal. bucket with sanitizing solution that is mixed to mfg. recommendations (50 to 100 PPM). Allow the bar gun whip assembly to soak in the solution for 10 to 15 minutes. Using a cloth and brush, wash and clean the hose.

  • Page 14: Troubleshooting

    TROUBLE SHOOTING A. Push water - no water dispensed • Check water supply • Check Shut-off (is it open) • Check ratio/brix adjustment • Check for proper butterfly plate B. Push syrup - no syrup dispensed • Check C0 pressure •...

  • Page 15: Line Configuration

    LINE CONFIGURATION 8 Button 10 Button END OF HANDLE END OF HANDLE S1 S2 S1 S2 SODA SODA S3 S4 S3 S4 S5 S6 S5 S6 WATER WATER S7 S8 S3 SODA WATER S4 S3 SODA WATER S4 12 Button 14 Button 808-0071 SODA...

  • Page 16: Juice And Energy Butterfly Plate Configurations

    JUICE AND ENERGY BUTTERFLY PLATE CONFIGURATION = Secondary Water Metering Screw Affects These Positions = Carbonated Positions ® = Requires Soda/Water Button Foot (P.N. 265-0039/265-0040) = Non-Carbonated Extensions Into Bottom Of Button Where Symbol Appears. Positions 805-0039C Rev F...

  • Page 17: And 10 Butterfly Plate Configurations

    8 AND 10 BUTTON BUTTERFLY PLATE CONFIGURATIONS 805-0039C Rev F...

  • Page 18: And 14 Butterfly Plate Configurations

    12 AND 14 BUTTON BUTTERFLY PLATE CONFIGURATIONS 805-0039C Rev F...
  • Page 19 12 AND 14 BUTTON BUTTERFLY PLATE CONFIGURATIONS 805-0039C Rev F...

  • Page 20: Button Plate Configurations

    BUTTON PLATE CONFIGURATIONS 659-0001 659-0007 10 BUTTON 8 BUTTON 5C/3NC, 6C/2NC, 6C/0NC 8C/0NC 659-0005 659-0003 14 BUTTON 12 BUTTON 6C/6NC, 6C/4NC, 8C/4NC 7C/3NC PLEASE CONTACT CUSTOMER SERVICE FOR OTHER PLATE CONFIGURATIONS 805-0039C Rev F...

  • Page 21: Accessories

    ACCESSORIES 805-0039C Rev F...
  • Page 22 ACCESSORIES ACCESSORIES PARTS LIST ITEM TAPRITE PN DESCRIPTION 675-0017-SP KIT, HOLSTER ASSY, W/SCREWS/BG, BLACK, 5/PK 315-0016 INSERT, HOLSTER, SHORT, BARGUN 265-0151 HOLSTER, BARGUN, BLACK 265-0152 DRIPTRAY, BARGUN, BLACK 208-5112-SP KIT, O-RING, 2-112, EPDM, 100/PK 265-0153 BRACKET, MOUNTING, BARGUN, BLACK 316-0004-SP...

  • Page 23: Handle Assembly

    HANDLE ASSEMBLY **NEW** for Rattler II 805-0039C Rev F...
  • Page 24 HANDLE ASSEMBLY BARGUN HANDLE PARTS LIST ITEM TAPRITE PN DESCRIPTION 220-0012-SP KIT, SCREW, 6-32 x .500, PH, PHD, SS, 50/PK 265-0039-SP KIT, BUTTON, WATER, OVAL, 50/PK 265-0040-SP KIT, BUTTON, SODA, OVAL, 50/PK 265-0007-SP KIT, ACTUATOR, SINGLE, 50/PK 265-0083-SP KIT, ACTUATOR, SINGLE, PREMIX, 50/PK...

  • Page 25: Manifold Assembly

    MANIFOLD ASSEMBLY 805-0039C Rev F...
  • Page 26 MANIFOLD ASSEMBLY BARGUN MANIFOLD PARTS LIST ITEM TAPRITE PN DESCRIPTION 265-0076-SP KIT, SCREW, SEPARATOR, 10/PK 808-0173-SP KIT, LABEL, HANDLE LAYOUT, 8B, 5/PK 808-0054-SP KIT, LABEL, HANDLE LAYOUT, 10B, 5/PK 808-0061-SP KIT, LABEL, HANDLE LAYOUT, 12B, 5/PK 808-0071-SP KIT, LABEL, HANDLE LAYOUT, 14B, 5/PK...

  • Page 27: Flow Control Module Assembly

    FLOW CONTROL MODULE ASSEMBLY 805-0039C Rev F...
  • Page 28 FLOW CONTROL MODULE ASSEMBLY BARGUN FLOW CONTROL MODULE PARTS LIST ITEM TAPRITE PN DESCRIPTION 224-0005-SP KIT, SCREW, 6-19 x .375, PLASTITE, PH, PHD, 100/PK 808-0363-SP KIT, LABEL, SODA, VALVE, COMPACT BG, 16/SHEET 808-0364-SP KIT, LABEL, WATER, VALVE, COMPACT BG, 16/SHEET...

  • Page 29: Mechanical Module Assembly

    MECHANICAL MODULE ASSEMBLY 805-0039C Rev F...
  • Page 30 MECHANICAL MODULE ASSEMBLY BARGUN MECHANICAL MODULE PARTS LIST ITEM TAPRITE PN DESCRIPTION 224-0005-SP KIT, SCREW, 6-19 x .375, PLASTITE, PH, PHD, 100/PK 808-0363-SP KIT, LABEL, SODA, VALVE, COMPACT BG, 16/SHEET 808-0364-SP KIT, LABEL, WATER, VALVE, COMPACT BG, 16/SHEET 808-0365-SP KIT, LABEL, S1, VALVE, COMPACT BG, 16/SHEET...

  • Page 31: Mounting Plate Screw Placement

    MOUNTING PLATE SCREW PLACEMENT PATENT & PATENT PENDING NUMBERS 805-0039C Rev F...

  • Page 32: Part Number Format

    NEW BAR GUN PART NUMBER FORMAT Bar Gun part numbers are formatted to capture all relevant information about a product so that it can be tracked for manufacturing, sale, troubleshooting and warranty purposes. As of 01/01/19, the format for the Bar Gun part number will be as follows: The legacy part number will still be referenced in your order confirmation, packing lists, and invoices.

  • Page 33: Apendix

    APENDIX SERVICING PLUNGER O-RINGS IN PREVIOUS VERSION HANDLES In order to complete this action, Technicians will need: 316-0028-SP – O-ring Insertion and Extraction Tool (also found in 675-0209 Rattler Service Kit) 208-4003-SP – 208-003, Blue VITON XP41 O-Rings (also found in 675-0209 Rattler Service Kit) Phillips Head and Flat Head Screwdrivers Foodgrade Lubricant To replace the O-Rings:...

This manual is also suitable for:

950cRattler ii 950c

Table of Contents