AiRide 2633 Installation Instructions Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

2633

ﬁrestoneairide.com

INSTALLATION INSTRUCTIONS

10-23

Table of Contents

Need help?

Do you have a question about the 2633 and is the answer not in the manual?

Questions and answers

Summary of Contents for AiRide 2633

Page 1 2633 ﬁrestoneairide.com INSTALLATION INSTRUCTIONS 10-23...
Page 2: Safe Installation
IMPORTANT PLEASE DON’T HURT YOURSELF, THE KIT, OR YOUR VEHICLE. TAKE A MINUTE TO READ THIS IMPORTANT INFORMATION. SAFE INSTALLATION Please take all safety precautions during installation. A hydraulic jack can fail, and if that happens, you can be seriously hurt, or worse, if you are relying on it to hold up the vehicle. If you use a hydraulic jack, secure jack stands in the appropriate locations and chock any tires still touching the ground.
Page 3 1 WIRE HARNESS x 1 INFLATION HOSE AIR COMMAND AIR TUBING DUAL REMOTE (22 FEET) A21-760-2633 HARDWARE PACK 10-32 x 1" 10-32 x 3/4" x 10 #10 FLAT WASHER MACHINE SCREW MACHINE SCREW 10-16 x 3/4" INFLATION VALVE...
Page 4 CONTENTS AND OVERVIEW PLANNING THE PAGE INSTALL 3055 1/8 NPT AIR FILTER PUSH-TO-CONNECT STRAIGHT FITTING PREPARE THE PAGE AIR COMPRESSOR 9499 AIR RED (+) COMPRESSOR Create DRILL HOLES FOR loop in Air PAGE AIR COMPRESSOR Tubing. AND ECU * As a water/debris trap.
Page 5: Planning The Install
Air Tubing down collar and Air Fitting. far as possible. to check for a gently pull Air secure ﬁt. Tubing away. Removal Tip: Use a 1/4 , 5/16 , or 6mm open-ended wrench to push the collar down. 2633 Installation Instructions...
Page 6 PREPARE THE AIR COMPRESSOR NOTE: Air Compressor can be mounted facing any direction. Install 1/8 NPT Push-to-Connect Straight Fitting on the Check Valve. 3055 1/8 NPT PUSH-TO-CONNECT STRAIGHT FITTING PRE-INSTALLED Tighten to engage two threads CHECK VALVE of thread lock. 9499 AIR COMPRESSOR ﬁrestoneairide.com...
Page 7 THE WIRE HARNESS WILL REACH THEM BOTH. 7/32" OPTIONAL ECU MOUNTING 9961 ECU If there is no other mounting option, 9961 ECU use at least two Large Nylon Ties to secure ECU to the location determined in planning the install section. 2633 Installation Instructions...
Page 8: Top View
INSTALL THE AIR COMPRESSOR AND ECU x 12 DO NOT OVER TIGHTEN MOUNTING BOLTS AND NUTS ON THE AIR COMPRESSOR. TOO MUCH TORQUE CAN CRUSH THE BRASS INSERTS AND RUBBER ISOLATORS. Mount the Air Compressor Mount the ECU to the drill Mount the black ground wire to the drill hole location hole location using the...
Page 9 Cut the Air Tubing at an angle. Use a tube cutter or very sharp utility knife. Use pliers, scissors, snips, saws, or side cutters. PROPER AND IMPROPER CUTS IN THE AIR TUBING Square cut AIR TUBING AIR TUBING AIR TUBING AIR TUBING 90˚ 2633 Installation Instructions...
Page 10 INSTALL THE WIRE HARNESS 9499 AIR RED (+) COMPRESSOR Why ground the Wire Route the Wire Harness in Harness to the battery? the most protected manner The ECU needs a good, clean ground for opti- possible, and securely make mal accuracy. The Air all connections as shown.
Page 11 Clean up the installation using supplied Nylon Ties, and return all factory parts and materials to operative state. USING SUPPLIED NYLON TIES, SECURE ALL WIRING AND AIR TUBING IN A MANNER THAT DOES NOT OBSTRUCT MOVING PARTS OR IN ANY WAY THAT AFFECTS YOUR ABILITY TO SAFELY OPERATE THE VEHICLE. 2633 Installation Instructions...
Page 12 ECU POWER UP/APP PERFORMANCE Download app from Google Play or Apple Store. Search for ‘Air Command Dual’. Start the vehicle and open app. Select SCAN and click on the ECU from the screen. Follow onscreen prompts to link to the ECU and press NEXT.
Page 13: Factory Reset
• If you select INSTALL, the ﬁrmware will begin to update. This will take approximately 3-4 minutes • Keep the app open during the update and stay within range of the ECU until complete • Once OTA is complete, restart the app, use the default passkey, and use as normal 2633 Installation Instructions...
Page 14 USING THE AIR COMMAND DUAL APP ™ MAIN SCREEN SETTINGS SETTINGS ICON CHANGE UNITS TURN TANK MODE ON/OFF, SET PRESSURES FOR TANK MODIFY MEMORY PRESSURES AND NAMES CONTROL AUX PRESSURES ACTUAL PRESSURE VERIFIES SYSTEM ISSUE WITH TROUBLESHOOTING STEPS SHOWS SYSTEM INFORMATION BLUETOOTH SETTINGS MEMORY BUTTONS (Tap to activate)
Page 15: System Fault
SLIDE TO MANUAL AND SYSTEM WILL FILL UNTIL TURNED OFF CLARIFIES INDICATOR CODE SLIDE TO AUTO AND SET PRESSURE ALLOWS USER TO CLEAR ACTUAL PRESSURE AND ACKNOWLEDGE DIAGNOSTICS SHOWS SYSTEM INFORMATION GREEN INDICATES WHAT PART IS ON VEHICLE BATTERY VOLTAGE 2633 Installation Instructions...
Page 16: Manual Mode
USING THE AUXILIARY PORT Select AUX PORT in the app settings menu MANUAL MODE (slide from OFF to MANUAL) • This will start the compressor and allow the user to monitor the air pressure that the auxiliary tubing is being used to ﬁll. •...
Page 17 THE SYSTEM IS CONTROLLED BY THE USER TO FILL EXTERNAL ITEMS. IT IS THE RESPONSIBILITY OF THE USER TO INFLATE TO THE APPROPRIATE PRESSURE DETERMINED BY THE MANUFACTURER OF THE ITEM. DO NOT EXCEED THE CAPACITY OF THE FIRESTONE COMPRESSOR FOR RUNTIME (DUTY CYCLE) OR PRESSURE 2633 Installation Instructions...
Page 18: Functions Of Remote Buttons
AIR COMMAND DUAL REMOTE QUICKSTART GUIDE ™ FUNCTIONS OF REMOTE BUTTONS USB-C Charging Port Set or Select Memory 1 Set or Select Memory 2 Increase Pressure/ Move Up Select Right Select Left Air Spring/ Air Spring/ Move Right Move Left/ Exit Menu Decrease Visor Clip...
Page 19 *Not Found is usually page. caused by the system not having power. *Remember, the default passkey is 123456. *Not Connected is usually caused by an incorrect Passkey. It has found the unit, but cannot connect. 2633 Installation Instructions...
Page 20: Menu Screen
AIR COMMAND DUAL REMOTE QUICKSTART GUIDE ™ MENU SCREEN Menu Pressing the center F-Shield Button provides access to the remote menu. All additional settings are available here. Use the Up and Down Arrow Buttons to navigate the menu. Press the Left Arrow to exit to the Home Screen.
Page 21 This page provides the with Dark Mode activated. current Firmware and The use has the ability to Hardware information for change between more or both the Remote and ECU. less LEDs lit depending on preference and ambient conditions. 2633 Installation Instructions...
Page 22 TEST THE SYSTEM With the Air Command Dual App and your Air Springs installed, you are ready to test the system. ™ Reattach the negative Use the Air Command Dual App ™ battery cable. or Dual Remote to inﬂate the Air Springs to 70 PSI.
Page 23 Refer to the Troubleshooting section of the Instruction Manual. If the leak persists, or if there is an issue with a leaking part, email us at rrtech@fsip.com. If emailing, please include photos to help us better diagnose and understand any problems you may be experiencing. 2633 Installation Instructions...
Page 24 2633 ﬁrestoneairide.com BEFORE YOU DRIVE, CONFIRM THE FOLLOWING: Secure all Air Tubing and wiring. The system passes the leak test and holds air. The Air Compressor ground ring terminal is contacting bare metal, and coated with silicone if possible. The Wire Harness is grounded to the negative (-) battery terminal. The ECU needs a good, clean, interference-free ground.