Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for EK-Quantum Reflection 2 PC-O11D EVO XL D5 PWM D-RGB
- Page 1 EK-Quantum Reflection PC-O11D EVO XL D5 PWM D-RGB DISTRIBUTION PLATE USER GUIDE...
- Page 2 Please note the installation of the product is intended to be undertaken by an adequately trained and experienced person. You are installing the product at your own risk. If you are not properly trained or experienced or feel unsure about the installation procedure, please refrain from installing the product yourself and contact our tech support for assistance.
-
Page 3: Table Of Contents
TABLE OF CONTENT BOX CONTENTS DISTRIBUTION PLATE DIMENSIONS TECHNICAL SPECIFICATIONS AND PRODUCT PARTS PREPARING THE 011D EVO XL CHASSIS INSTALLING THE DISTRIBUTION PLATE RECOMMENDED DISTRIBUTION PLATE CONFIGURATIONS ATTACHING THE PUSH-IN ADAPTERS (OPTIONAL) FLOW DIAGRAM CONNECTING THE D-RGB LED STRIP CONNECTING THE PUMP TESTING THE LOOP SUPPORT AND SERVICE SOCIAL MEDIA... -
Page 4: Box Contents
BOX CONTENTS Mounting Mechanism EAN: 107076 EK-Loop Multi Allen Key (1 pc) Allen Key 2.5 mm (1 pc) Allen Key 2 mm (1 pc) EK-Quantum Reflection PC-O11D EVO XL D5 PWM D-RGB - 4 -... -
Page 5: Distribution Plate Dimensions
DISTRIBUTION PLATE DIMENSIONS 230 mm 188.6 mm 163 mm 160.6 mm 132.6 mm 107 mm 69.8 mm 79 mm 29 mm 47.5 mm 49 mm - 5 -... -
Page 6: Technical Specifications And Product Parts
107072 OR - Reflection EVO XL 6-6 8311 Screw M4 x 20 DIN7984 9039 Screw M4 x 18 DIN7991 9044 Screw M4 x 8 DIN7991 106946 Bottom plate (Plexi) EK-Quantum Torque Push-In 3831109895313 Adapter 3831109834282 Plug Cover - 6 -... -
Page 7: Preparing The 011D Evo Xl Chassis
PREPARING THE 011D EVO XL CHASSIS STEP 1 Unscrew the factory-provided screws and remove the top panel from the case. STEP 1 STEP 2 Remove both side panels and the front panel from the case. STEP 2 - 7 -... -
Page 8: Installing The Distribution Plate
STEP 3 Using the Philips Head Screwdriver, unscrew the factory-provided SIDE PANEL side panel screws and remove the side panel. Save the screws for SCREW later steps! For this step you will need: SIDE PANEL Phillips-head screwdriver STEP 3 INSTALLING THE DISTRIBUTION PLATE STEP 1 Important! Before placing the distribution plate, you must install the radiators in the following order:... - Page 9 STEP 2 Position the distribution plate into the PC Case. Make sure to align the mounting holes. Be careful not to scratch the acrylic parts! STEP 2 STEP 3 Secure the distribution plate using the saved Side panel screws. The SIDE PANEL screws shouldn’t be over-tightened to avoid cracking the acrylic.
-
Page 10: Recommended Distribution Plate Configurations
RECOMMENDED DISTRIBUTION PLATE CONFIGURATIONS To complete your loop, all ports must be used as marked in the image. TOP RADIATOR OUTLET (TRIPLE RADIATOR All remaining unused ports must be closed with supplied plugs, CONFIGURATION) using the EK-Loop Multi Allen Key. SIDE RADIATOR OUTLET If one of the prescribed components will not be installed... - Page 11 FILL PORT (DRAIN PORT IN FLIPPED CONFIGURATION) DRAIN PORT (FILL PORT IN FLIPPED CONFIGURATION) - 11 -...
-
Page 12: Attaching The Push-In Adapters (Optional)
ATTACHING THE PUSH-IN ADAPTERS (OPTIONAL) The push-in adapters can be attached to the marked places in the diagram. For easier push-in adapters’ installation, EK recommends lubricating the O-rings with a few drops of coolant or water. Important! Only the M7 Push-in Adapters are compatible with this distribution plate! - 12 -... -
Page 13: Flow Diagram
FLOW DIAGRAM - 13 -... -
Page 14: Connecting The D-Rgb Led Strip
CONNECTING THE D-RGB LED STRIP Plug the 3-pin connector of the distribution plate D-RGB LED light to the D-RGB HEADER on the motherboard. The LED will work if the pin layout on the header is as follows: +5V, Digital, Empty, Ground. D-RGB Header RGB Header CONNECTING THE PUMP... -
Page 15: Testing The Loop
TESTING THE LOOP To make sure the installation of EK components was successful, we recommend you perform a leak test for 24 hours. When your loop is complete and filled with coolant, connect the pump to a PSU outside of your system. Do not connect power to any of the other components. -
Page 16: Support And Service
SUPPORT AND SERVICE In case you need assistance or wish to order spare parts or a new mounting mechanism, please contact: https://www.ekwb.com/customer-support/ For spare parts orders, refer to the page with “TECHNICAL SPECIFICATIONS AND PRODUCT PARTS” where you can find the EAN number of each part you might need.
Need help?
Do you have a question about the Reflection 2 PC-O11D EVO XL D5 PWM D-RGB and is the answer not in the manual?
Questions and answers