Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for BESV SMALO LX2
- Page 1 SMALO LX2/PX2 HMI User Manual...
-
Page 2: Table Of Contents
SMALO LX2/PX2 HMI User Manual CONTENTS Introduction ..........................2 Manufacturer Information ........................2 Product Description ..........................2 Support Information ..........................2 Copyright Information ..........................2 SMALO’s HMI ..........................3 HMI Guide ..............................3 How to Power ON/OFF ..........................3 Detailed Icon Explanations ........................4 Battery Capacity..........................4 USB Type-C Charger Port ........................4 Additional Useful Information .................... -
Page 3: Introduction
SMALO LX2/PX2 HMI User Manual Introduction Manufacturer Information Darad Innovation Corporation is a company located in Taiwan. We are committed to developing products that feature innovative ideas and structures. Product Description Product Description: Stem Integrated HMI Trademark: SMALO Type Designation: 60.Y2XHM.001 / 60.Y3BHM.001... -
Page 4: Smalo's Hmi
Typically, the HMI turns on when you turn on the e-bike’s power. (The figure below shows how to turn on SMALO LX2’s power. SMALO PX2 can be powered on the same way, with the power button at a similar location—top tube.) -
Page 5: Detailed Icon Explanations
SMALO LX2/PX2 HMI User Manual Detailed Icon Explanations Battery Capacity 81%-100% 61%-80% 41%-60% 21%-40% 11%-20% <10% Indicates that the battery level is almost at 0% and will be turning OFF power shortly. ［Note］Orange color indicates blinking. USB Type-C Charger Port The USB Type-C Charger Port is water-resistant. - Page 6 SMALO LX2/PX2 HMI User Manual Caution To avoid electric shock and damage to the e-bike, HMI, or your device, do not plug in any device while the charger port and/or the charging cable plug is wet. You should still ensure that the charger port on the HMI and charger plug for your rechargeable device are dry and clean before use.
-
Page 7: Additional Useful Information
SMALO LX2/PX2 HMI User Manual Additional Useful Information Disposal and recycling Information In the future, when this product reaches its end of life or when you need to dispose of it for any reason, please take note of the following: Important Information •... -
Page 8: Troubleshooting
SMALO LX2/PX2 HMI User Manual Troubleshooting Warning Codes Component Code Description User Action Controller Unstable communication If the battery is removable, please turn (1~16) between the controller and the off the power, reinstall the battery, then battery turn on the system again. - Page 9 SMALO LX2/PX2 HMI User Manual Abnormal USB power supply Turn off the power and remove cable and rechargeable device. After turning on the power again, please try changing the USB cable and the rechargeable device. Cross check to verify which has failed.
-
Page 10: Error Codes
SMALO LX2/PX2 HMI User Manual Error Codes Components Code Description User Action Controller Motor stall is detected Please restart the system. If the error (1~31) persists, please contact our service center. Speed sensor error Please restart the system. If the error persists, please contact our service center. - Page 11 SMALO LX2/PX2 HMI User Manual Controller is overheating It is the bike's protective measure due to challenging riding/environmental conditions. Please turn off the system and wait for at least 60 minutes to allow system to cool down. Afterwards, turn on the system; if the error persists, please contact our service center.
- Page 12 SMALO LX2/PX2 HMI User Manual E-Lock Undervoltage in the electric lock Use the correct charger to charge to (32~39) full capacity, and check if the error is resolved. If not, please contact our service center. Electric lock motor operation If the error persists, please contact timed out our service center.
- Page 13 SMALO LX2/PX2 HMI User Manual HMI button signal error (Analog If the error persists, please contact type) our service center. HMI button signal error (Digital If the error persists, please contact type) our service center. Passcode error Please enter the passcode again. If you have forgotten it, you can use the app to change the passcode.
- Page 14 SMALO LX2/PX2 HMI User Manual Battery Over Current Charge Please restart the system. If the error (OCC) Protection persists, please contact our service center. AFE Fault Protection Error for Please restart the system. If the error Battery persists, please contact our service center.
-
Page 15: Safety Information
• Consult the dealer or an experienced radio/TV technician for help. Changes or modifications to this product not authorized by SMALO by BESV could void the electromagnetic compatibility (EMC) and wireless compliance and negate your authority to operate the product. -
Page 16: Specifications
SMALO LX2/PX2 HMI User Manual Specifications Item Spec. Model Operating voltage 5 ± 0.1V Rating power a. with right switch:0.35W consumption b. without right switch: 0.25W a. with right switch: 0.8W Max power consumption c. without right switch: 0.5W a. with right switch: 115g Weight b.
Need help?
Do you have a question about the SMALO LX2 and is the answer not in the manual?
Questions and answers