Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for jcm-tech HONOARELAY
Summary of Contents for jcm-tech HONOARELAY
- Page 1 HONOARELAY User Manual...
-
Page 2: Table Of Contents
Table of contents Important safety instructions Use of the equipment Introduction General description Features Installation Connection Electric lock or suction cups Configuration Connect to the Internet Configuration with cloudAssistant Registering the equipment Registering groups and users Configure relays and assign traffic schedules Set group schedules Administration: Honoa Events... -
Page 3: Important Safety Instructions
Important safety instructions Disconnect the power supply whenever you proceed to the installation or repair of the equipment. In compliance with the European Low Voltage Directive, we inform you of the following requirements: •When the devices remain permanently connected, an easily accessible connecting device must be incorporated into the wir- ing. -
Page 4: Introduction
HONOARELAY, together with cloudAssistant, allows you to manage permissions of the users of the HONOA APP and also allows you to check the operation of the door from the office and instantly, avoiding unnecessary trips to verify installations that work correctly. -
Page 5: Features
Features Power supply: The equipment is powered with a 12/24Vdc. The device has protective fuse. Relay Output: The equipment has 2 adjustable open or closed contact relay outputs. These outputs can be programmed to be activated with different fob channels through cloudAssistant. Moreover, these relays can be remotely activated in real time with the cloudAssistant. - Page 6 jcmtechnologies...
-
Page 7: Installation
Attach the back of the box to the wall with the plugs and screws supplied. Connection HONOARELAY installation sketch with layout for inputs to monitor the door's status with limit switches. POWER INPUT. 12/24Vdc power supply. Relay 1 Output:Channel 1 relay, contact normally open.. -
Page 8: Electric Lock Or Suction Cups
Electric lock or suction cups The relays can switch up to 2A of resistive loads. The number of manoeuvres depends on the type and characteristics of the loads. With resistive loads, they can reach 1000000 manoeuvres with 30W loads. DC inductive loads: 30W / 30Vdc / 1A -> 500000 manoeuvres. One diode (1N4007) along with the electric lock or suction cups is necessary in parallel. -
Page 9: Configuration
Configuration Connect to the Internet The device must be connected to the Internet to change its settings, but it does not require a connection to function. With the device connected to a power source, check that the ST LED is blinking green, and that the NW LED is blinking in red. -
Page 10: Configuration With Cloudassistant
Configuration with cloudAssistant Registering the equipment Once the equipment has an Internet connection, it can be configured: Enter cloudAssistant:https://cloudassistantv4.jcm-tech.com/login and login. Add facility (orange button located in the lower right corner). Fill the fields. Save. The name of the installation and the city will appear in the HONOA APP:... - Page 11 Equipments -> Add equipment (orange button located in the lower right corner). Enter a name for the device and select HONOARELAY. Save. The name of the device will appear in the HONOA APP: jcmtechnologies...
- Page 12 Enter the Activation Key (found in the device label). Select the pertinent Timezone and assign names and work modes to the entries. Save. The names assigned to the entries are the same ones that appear in "Remote state" (see: Operational Mode). The Activation key and the Timezone are the only mandatory fields to register users when the device is disconnected.
-
Page 13: Registering Groups And Users
Registering groups and users Groups -> Add (orange button located in the lower right corner). Enter Name and Description. Save. jcmtechnologies... - Page 14 Activate the relays by selecting any of the channels. HONOA activates relays. Back. If this is a group of devices working with fobs, the selected channels match the function that the fob will have. On the group screen: Add user to add HONOA users. jcmtechnologies...
-
Page 15: Configure Relays And Assign Traffic Schedules
Complete the fields with the user information. Accept. The different users must provide the email used for their Honoa account. When a user is registered with cloudAssistant, they will automatically have access to the install- ation with the Honoa application. Click "Installation Name"... - Page 16 •Relay X: assign name to the relay •Selector: enable/disable relay •Relay type X: Normally open/ Normally closed •Relay activation time X: set the time that the relay remains active for (it is 1 second by default) •Relay delay time X: set the time that it takes for the relay to activate (it is 0 seconds by default) •Open door schedule: The relay activates automatically, based on the assigned weekly hours.
-
Page 17: Set Group Schedules
Set group schedules The assignment of a schedule to a group is done in the "Configuration" screen of groups: Group users can only activate the relay when within the assigned hours. If there is no assigned schedule, it can always be activated. -
Page 18: Administration: Honoa
Administration: Honoa HONOA users may view your contact information by clicking on the logo to the bottom left of the device in the HONOA APP. Contact information can be changed on the "Honoa" screen under "Administration". jcmtechnologies... -
Page 19: Events
Events HONOARELAY is a device with an event record. To see them, in cloudAssistant, go to the device's "Events" screen. When HONOARELAY does not have an Internet connection, the device keeps working, but without sending the events in real time. In this case, the events are stored locally on the device. To load the list of events from the device, go to the "Events"... -
Page 20: Operational Mode
Operational mode Remote control from cloudAssistant To control the equipment remotely it is necessary to have it connected to the Internet: •Go to "Facilities" -> "Facility name" -> "Equipments"-> Select "Remote State" (button with the door). We can view the status of the inputs and remotely activate the equipment's relays. You also have information on the equip- ment (equipment versions, connection levels, etc.). -
Page 21: Verification
Verification LED behaviour FIXED BLINKING State Status LED Network LED Internet LED Action Power off No Firmware CALL TECHNICAL SUPPORT Starting WAIT Use embedded web or WPS to Wi-Fi/GSM Configuring configure connectivity Wi-Fi/GSM Configuring Reset device timeout Connecting Wi-Fi/GSM WAIT WRONG WI-FI/GSM WIFI/GSM Error PASSWORD... -
Page 22: Notes
Notes jcmtechnologies... - Page 23 Notes jcmtechnologies...
-
Page 24: Technical Data
5000 users Regulatory Data UKCA Declaration of conformity The manufacturer JCM TECHNOLOGIES, SAU declares that the product HONOARELAY complies with the relevant fun- damental requirements of the Radio Equipment Regulations 2017 and of the RoHS Regulations 2012. EU Declaration of conformity The manufacturer JCM TECHNOLOGIES, SAU declares that the product HONOARELAY complies with the relevant fun- damental requirements of the RED Directive 2014/53/EU and of the RoHS Directive 2011/65/EU.