Do you have a question about the 18151BX and is the answer not in the manual?
Questions and answers
Summary of Contents for VEVOR 18151BX
Page 1
Technical Support and E-Warranty Certificate www.vevor.com/support SUCTION POOL CLEANERS USER MANUAL We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and doses not necessarily mean to cover all categories of tools offered by us.
Page 2
CustomerService@vevor.com This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product.
Safety Instructions Thanks to its easy assembly, you’ll be able to use your automatic cleaner in a few minutes. Follow the instructions carefully and SAVE THIS MANUAL Assembly precautions 1.Assemble only according to these instructions. Improper assembly can create hazards. 2.Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
Components List 1.Install disk "A" onto the main body "B" and clip it into the groove of the foot pad. 2.Install the steering wheel "C" on to the main body "B". 3.Fix the steering wheel by screwing nut "J". - 3 -...
“B” Components List Preparatory Work 1.Turn off the pump of your pool. The Pump for the cleaner should have a minimum power of 0.5HP/1000gallons. - 4 -...
Page 6
2.Replace the eyelet of your return inlet with part "l", ensuring that the opening faces downward so as not to interfere with the operation of the cleaner. If your pool is equipped with a vacuum plug, follow step #3. If not, go directly to step 3.Connect part "H"...
Page 7
5.Connect the hose sections "D" and finish with section "E". 6.Place the weight "K" onto the third hose section and slide & click it backward or forward to adjust the buoyancy of the hoses and angle of cleaner in use. 7.Fill the hoses with water to eliminate the air pockets.
Page 8
No leak is allowed at the joint of the hoses. 8.Use enough hose sections to reach the farthest point in the pool. Always keep the hose lay straight when storage. - 7 -...
Page 9
9.If your regulator is connected to a vacuum plug, then connect the hose "E" directly to the regulator"G". If your regulator is connected to a wall skimmer, then pass the hose through the skimmer mouth and connect it to the regulator via the elbow "F".
Page 10
11.Turn on the pump and relax as your cleaner cleans your pool. 12.You can adjust the power of your cleaner by turning the knob of the regulator "G" as shown. - 9 -...
Page 11
13.If the cleaner leans too far forwards or backwards during operations, this can be corrected by moving the weight "K" along the tube section as shown in the drawing. How to Change the Diaphragm 1.Pull out the diaphragm together with "B4" (Make sure the white small clip must be set back on the new diaphragm).
2.Insert the assembled part back into the cleaner. Trouble Shooting Guide PROBLEM POSSIBLE SOLUIONS ● Check if the pump is ON or primed. ● Check t h e c leaner head for blockages. ● Clean and empty pump basket and empty skimmer/ weir basket.
Page 13
● Check the hose for blockage. ● Check the hose for leaks by lifting each section above water while pump is running. ●Check the diaphragm for blockages, and clean and empty it if blocked. Noted that if too many chemical tablets are used, the service life of diaphragm will be shorter.
Page 14
● Twist each hose section a half- turn at each connection point. ● Ensure the wheel at the top of the Cleaner head is rotating freely. ● Ensure there is a valve installed in the Cleaner skimmer/ weir. climbs out ●...
Page 15
move more freely. of the pool. ● Ensure the wheel on top of the Cleaner body Cleaner is rotating freely and is screwed on securely. leaves ● Adjust return jets downwards. patches. ● Verify proper hose length. ● Ensure cleaner sits flush with the pool floor. Adjust the position of hose weight if necessary.
Page 16
● Ensure the cleaner hose is assembled tightly. Air bubbles ● Ensure cleaner head is not removed from the water while pump is running. noticeable in ● Ensure the hoses are not damaged. the return ● Ensure the regulator valve is underwater. jets.
Page 17
Address:Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai Imported to AUS: SIHAO PTY LTD, 1 ROKEVA STREETEASTWOOD NSW 2122 Australia Imported to USA: VEVOR STORE INC, 9448 RINCHMOND PL #E RANCHO CUCAMONGA, California, 91730 United States of America Pooledas Group Ltd Unit 5 Albert Edward House, The Pavilions...
Page 18
Technical Support and E-Warranty Certificate www.vevor.com/support...
Need help?
Do you have a question about the 18151BX and is the answer not in the manual?
Questions and answers