Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Floorcare.biz X20BT
- Page 1 Walk-behind Floor Scrubber Instructions for operation and maintenance...
-
Page 2: Table Of Contents
CATALOGUE List Optional parts INTRODUCTORY COMMENT TECHNICAL DESCRIPTION SYMBOLS USED I N THE MANUAL GENERAL SAFETY REGULATIONS I, MACHINE PREPARATION HANDLING THE PACKED MACHINE HOW TO UNPACK THE MACHINE OVERALL INTRODUCTION INSERTING THE BATTERIES CONNECTING THE BATTERIES TYPE OF BATTERY7 BATTERYMAINTENANCE BATTERY DISPOSAL RECHARGING THE BATTERIES... -
Page 3: List
scrubber drying instnlttiOns for aperation and maintenance List Standard Packing Ust Older name unit quantity Machine Charge cable Battery cable piece Squeegee assembly Sudionpipe piece Manual piece a c certificate piece Optionalpa11s Pad holder 21 inch Front squeegee blade rubber grease proof Rear squeegee blade rubber grease proof INTRODUCTORY COMMENT... -
Page 4: Technical Description
s c r u b b e r cl,ving Instructions Ol)el'atfon a n d m a i n t e n a n c e TECHNICAL DESCRIPTION Working Width W i d t h Squeegee Max. FOtwatd Speed K m / h Max. -
Page 5: Symbols Used I N The Manual
scrubber drying Instructions for operation and maintenance SYMBOLS USED I N THE MANUAL & Recyde Attention Information Manual & Warning corrosion h Your Hand Caution shock Warning Injure hand Dangerous waste No open flames Caution Danger of exhalation of gas 3/18... -
Page 6: General Safety Regulations
SCl\lbber drying Instructions for operation and maintenance GENERAL SAFElY REGUlATIONS The regulations below must be ca,efully followed In on!er to avoid hann to the operator and damage to the machine. Read the labels on the machine carefully. Do not cover them for any reason and replace them immediately if they become damaged. -
Page 7: I, Machine Preparation Handling The Packed Machine
saubber drying in5tructiolls for operation and malntenance Make sure the whole electrical connection is recovered after maintenance. Do not remove any protection devices which require the use of special tools. Do not wash the machine with corrosive substances or with pressurized water. Send Iha machine to a Service Center nearby for servicing after 200 hours of use. -
Page 8: Overall Introduction
scrubber drying Instructions for Ol)eratlon and maintcnanre OVERALL INTRODUCTION A ; handle switch C : Voltmeter Squeegee lifting rod E : b rush switch F : Cap ol lhe drainage G : Filter · Squeegee switch magnetic valve Angle adjuster K : Brush Jumper cables M : Battery connector... -
Page 9: Inserting The Batteries
saubber- c1,ytn9 ln5tJucllons for c,peration and maintenance INSERTING ll-lE BATTERIES ( apply to A-58 ) The batteries should be correctly placed in the battery box below Iha recovery tank. The type of battery must comply wilh CE121-5 description. Inserting the batteries as follows ( as figure): Raise the recovery tank backwards. -
Page 11: Assembling The Squeegee
scrubber drying Instructions for operation and maintenance ASSEMBLING THE SQUEEGEE For packaging reasons, the squeegee is supplied disassembled from the machine, and must be assembled on the machine connection. Fix the squeegee lo the Support frame assembly (Q) with bolt as figure. Then connect the Suction pipe (T) to the squeegee , . - Page 12 scrubber drffng lnstluctions for operation and maintenance RECOVERY TANK Rotate the recovery tank as far as it will go, using the side handle. Check the suction tube (T), the drainage tube(S) and the recovery tank Is correctly connected. Check the suction tube (T) and the squeegee (P), the drainage tube(S) and the cap of drainage tube (F) Is correctly connected further.
-
Page 13: Assembling The Brush 1
saubber drytng insUucllolls for operation and mainlenance ASSEMBLING THE BRUSH •o- position turn 1. At first, tum the key (8) t o off the power. � i s operation must be canfed out after switch off the power supply protect your hands. 2. -
Page 14: Ii.work
scrubber drying lnstructlons for operation and maintenance II.WORK PREPARING TO WORK 1. Connect the connector (M) to the batteries; 2. Tum the key (B) of the main switch to position ·1· .The monitor (H) on the instrument panel will immediately come 3. -
Page 15: Overflow Device
scrubber drying instructions for operation and maintenance OVERFLOW DEVICE The machine i s fitted with a float which intervenes when the recovery tank i s full, causing the suclion lube lo close. I n this case, to avoid harming the motor, I t i s MUST t o empty the recovery tank, This operation must b e carried out using gloves lo protect against contact with dangerous solutions. -
Page 16: Ill, Dailymaintenance
operation scrubber d,ytng Instructions for and maintenance i l l . DAILY MAINTENANCE CLEANING THE RECOVERY TANK 1 . Remove the Sewage pipe(S) Remove the cap and empty the tank. £ carried These operations must using gloves to protect against contact with dangerous solutions 3. -
Page 17: Cleaning The Battery Box 1
50\Jbber dr,tng lnslrucllons for operation and mDlnlenanc.e CLEANING THE BATTERY BOX Whenever keep Iha battery and box clean with duster. Check out jumper cables end insulation base to make sure connecting firmly. If not it will lead to the jumper cables heal Then the battery will be under Iha influence of that �... - Page 18 scrubber drying Instructions for operation and maintenance REPLACING THE SQUEEGEE RUBBERS Check the state of wear and tear of the squeegee rubbers and, if necessa,y, replace them as below: 1 . Remove the tube <n from the sleeve (P) on the squeegee. 2 .
- Page 19 scrubber dl)ling instructions for operallOn and maintenance V. TROUBLE SHOOTING Before you take it to repair or call our customer service to help.you should check out those problems. Reason Phenomena Method Plug in the power and make sure Check out whether electricity is good Brush motor the fuses are normal work ;...
- Page 20 !:Ctub� drying instructions for opc,-atlcn and maintenance VI. CHOOSING AND USING THE BRUSHES POLYPROPYLENEBRUSH(PPL) Used on all types of Roors. Good resistance to wear and tear, and hot water (no greater than ° C ) . The Polypropylene brush is non-hygroscopic and therefore retains its characteristics even when working in wet conditions.