Page 1
Owner Manual Euro Bale Spear EBS-1 Read, Understand, and Follow this manual which provides information MADE IN THE USA and procedures to safely operate and maintain the attachment.
1. Introduction 1.3 Specifications Specifications subject to change without notice. 1.3.1 EBS-1 Specifications The Norden Euro Bale Spear is an attachment that mounts to a utility tractor equipped with a loader Overall Width 42" having the ability to quick attach to attachments Overall Length 50.25"...
1.6 Disposal of Equipment at End of Useful Life The Norden Mfg LLC bale spears are designed for the specific purpose of moving large bales of hay and straw. When this bale spear is no longer capable of performing its intended use, it should be dismantled and scrapped.
MAY result in minor or moderate injury. Norden Mfg LLC cannot anticipate every possible circumstance that might involve a potential hazard. NOTICE The warnings in this manual and on the product are, therefore, not all-inclusive.
Rollover hazard Stop engine STOP Not a lifting device Visibility - slow moving vehicle (SMV) Entanglement hazard Set parking brake 2.3.2 Prohibited Actions Do not alter or modify Do not leave out tools Euro Bale Spear Norden Mfg. LLC (877) 296-5851...
2.11 Training Falling Hazard Norden Mfg LLC follows the general Safety Do not allow riders on the machine Standards specified by the Farm Equipment or attachment at any time. Falling can result in Manufacturers Association (F.E.M.A.), and the severe injuries or death.
If you do not understand any information in this manual, see your dealer or contact Norden Mfg LLC before proceeding. Do not use or allow anyone else to use this attachment until all information has been reviewed.
Page 10
Authorization / Training Sign-Off Form Date User’s Signature Owner’s Signature Norden Mfg. LLC (877) 296-5851 Euro Bale Spear...
5. Replacement parts must have replacement decals attached before the bale spear is used. 6. Decals are available from your authorized dealer or from Norden Mfg LLC at no charge. Euro Bale Spear Norden Mfg. LLC (877) 296-5851...
Premature failure of spear may result from improper tightening of the spear nut. The operator should periodically make sure the nut is properly tightened (516 ft/lb or 700 N·m). Failure to do so may shorten the life of the spear. Norden Mfg. LLC (877) 296-5851 Euro Bale Spear...
Be familiar with all controls before using this attachment. Users who have not read and understood all operating and safety instructions are not qualified to use the attachment. Euro Bale Spear Norden Mfg. LLC (877) 296-5851...
2. Tilt the tool carrier forward completely to angle the in position. The lock lever is released and moves carrier arms downward toward the attachment. to the “locked attachment” position. Position the tool carrier an inch below the Norden Mfg. LLC (877) 296-5851 Euro Bale Spear...
It is important to note that these manuals the attachment raised off the ground. must be read and explained to any operator who cannot read. It is crucial to never allow anyone to operate the machine or use the attachment without Euro Bale Spear Norden Mfg. LLC (877) 296-5851...
Never attempt to stop a rolling bale machine while operating the loader can seriously damage with the machine. the machine and/or its hydraulic cylinders or hoses. Instead, first tip the bale up on the round side. Norden Mfg. LLC (877) 296-5851 Euro Bale Spear...
Plan your route to avoid heavy traffic. Travel on roadways in such a way that faster moving vehicles can pass safely. Norden Mfg. LLC (877) 296-5851 Euro Bale Spear...
8.2 Removing from Storage 1. Attach the bale spear to the machine following the procedure in section “6.3 Attaching to Machine” on page 16. 2. Before placing the bale spear back into service, replace any worn or defective parts and perform the “6.4 Pre-Operation Checklist” on page 17. Euro Bale Spear Norden Mfg. LLC (877) 296-5851...
Crush Hazard spear life and is an invitation for problems. Always set the bale spear on blocks or on Norden Mfg LLC will not claim responsibility for use the ground when performing maintenance. of unapproved parts and/or accessories and other damages as a result of their use.
9.3 Bolt Torque Requirements 9.4 Welding Repairs Before performing any type of welding repair WARNING to the attachment frame, contact Norden Mfg LLC for approval. Repair welding must be Equipment Failure done with care and with procedures that may be The proper torque value for bolts and beyond the capabilities of the ordinary welder.
23. Annually Make sure all fasteners are tightened to proper torque. Refer to “9.3 Bolt Torque Requirements” on page 23. Inspect and replace damaged safety decals or instructional labels. Wash the attachment. Inspect attachment frame for cracking or damage. Norden Mfg. LLC (877) 296-5851 Euro Bale Spear...
10. Parts Section 10.1 Ordering Parts Norden Mfg LLC manufactures a quality product that requires very little maintenance or repair. However, should a part break or become damaged, our knowledgeable staff can make sure you receive the part(s) to put your bale spear back into operation. 10.2 Contact Information...