Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for KISTERS HydroMet OSS-B1
Summary of Contents for KISTERS HydroMet OSS-B1
- Page 1 User Manual OSS-B1 12-2023 – 01-04-002 12-2023 – 01-04-002...
-
Page 2: Table Of Contents
Repair Part V Replacement of Cable Ends ......................14 Part List ............................. 16 Technical Data Part VI Obligations of the Operator and Disposal Part VII Obligations of the Operator ...................... 24 Dismantling / Disposal ....................... 24 © 2023 | KISTERS... -
Page 3: I Disclaimer
KISTERS has been advised of the © 2023 | KISTERS. Any rights not expressly granted herein possibility of such damages. -
Page 4: Scope Of Delivery
1 × Wading Rod of length 1.8 m in 3 sections (3 × 0.6 m), 20 mm diameter Accessories are available and must be ordered separately: § Current Meter Counter: PVD200 § Fans: type 1, 2 and 4 (for details see ch. Technical Data § Tail Fin Stem Assembly © 2023 | KISTERS... -
Page 5: Safety Instructions
Safety Instructions § Read the user manual including all operating instructions prior to installing, connecting and powering up the KISTERS OSS- B1. The manual provides information on how to operate the product. The manual is intended to be used by qualified personnel, i.e. -
Page 6: Part I Introduction
All current meters manufactured by KISTERS are calibrated in our purpose built high velocity rating tank prior to shipment. This rating tank is considered as best in the world since it can run at a velocity of 0.005 m/s minimum and 8 m/s maximum with a velocity resolution of ±0.001 mm... -
Page 7: Part Ii Operation
Fan assembly. The capillary oil passage between the stainless steel axle (5) and Fan carrier (6), prevents entry of water to the bearings. A locknut on the shaft locates the bearings and sets the end float of the assembly. Figure 1 © 2023 | KISTERS... - Page 8 Operation Figure 2 Figure 3 Figure 4 © 2023 | KISTERS...
-
Page 9: Part Iii Maintenance
Drain the old oil from the fan in a recycling container (for environmental reasons, do not pour white spirits on the ground). § Put the bearing end of the spindle assembly into the cleaning jar and gently agitate. © 2023 | KISTERS... -
Page 10: Service And Recalibration
Return spare parts back into the cleaning container and store in the carrying case. Service and Recalibration § Recalibrate the current meter every 300 hours of use or once a year whichever comes first (see KISTERS calibration certificate for details). §... - Page 11 Faulty plug contact. Check fit of plug in hole. Open circuit between plug (11) and § § Faulty insulated contact assembly Remove, wipe surface clean and insulated reed switch contact (Figure 3 check spring compression. (Figure 3 © 2023 | KISTERS...
- Page 12 No closure of reed switch contact when magnet in position. § § Faulty earth contact (12) (Figure Check spring compression. Remove Reed switch operating but signal not assembly and wipe clean contact passing to body. surfaces with silicon grease and re- assemble. © 2023 | KISTERS...
-
Page 13: Part V Repair
§ Please do not ship the goods prior to obtaining the reference number. KISTERS will not reject any equipment that arrives without reference number; however, it may take us longer to process. Custom requirements for items sent to KISTERS for warranty or non-warranty repairs: Check with your national customs/tax authorities for details, processes and paperwork regarding tax exempt return of products. -
Page 14: Replacement Of Cable Ends
Position heat shrink sleeve centrally over grey cable insulation and fix in place Note: Repair to either plug end individually can be made also, by only cutting away the damaged end and following steps b, d & e. Figure 5 © 2023 | KISTERS... - Page 15 2 and 7. However, the shortened ends of the cable might be difficult to assemble conveniently onto the current meter, and it is usually preferable to reconstruct the cable as detailed in figure 6. Figure 6 © 2023 | KISTERS...
-
Page 16: Part List
Repair Part List © 2023 | KISTERS... - Page 17 Repair © 2023 | KISTERS...
- Page 18 Repair © 2023 | KISTERS...
- Page 19 Repair © 2023 | KISTERS...
- Page 20 Repair © 2023 | KISTERS...
- Page 21 2 - 3 metres Point WR04-01 Foot Plate WR04-02 Canvas Carrying Bag for 3 m wading rod sets WR05 Fixing Screw SAN20-04 Screwdriver SC002-06 METER RELOCATING DEVICE, STAINLESS STEEL, 1 METRE SECTION Rod Section RD01 Locking Tool RD03 © 2023 | KISTERS...
- Page 22 Repair Universal Wading Rods & Relocating Devices © 2023 | KISTERS...
- Page 23 Technical Data Technical Data Accuracy ±1 % § Each current meter individually calibrated in KISTERS’ calibration tank Calibration § Compliant with ISO 3455:1976 and ISO 2537:1988 § Calibration certificate delivered with each current meter Propeller The choice of fan / propeller depends on the specifics of the site such as discharge and the Specifications geometry of the riverbed or channel.
-
Page 24: Part Vii Obligations Of The Operator And Disposal
Instead, these old appliances must be collected separately and disposed of via the local collection and return systems. Integrated or provided batteries and accumulators must be separated from the appliances and disposed of at the designated © 2023 | KISTERS... - Page 25 At the end of its service life, the lithium-ion battery must be disposed of according to legal provisions. EU WEEE Directive As players in the environmental market, KISTERS AG is committed to supporting efforts to avoid and recycle waste. Please consider: §...
- Page 26 +64 7 857 0810 sales@kisters.co.nz www.kisters.co.nz Latin America | KISTERS Latin America +57 350 575 4079 sales@kisters-latam.com www.kisters-latam.com North America | KISTERS North America +1 561 459 4876 kna@kisters.net www.kisters.net Spain | KISTERS Ibérica info@kisters.es www.kisters.es © 2023 | KISTERS...
- Page 27 © 2023 | KISTERS 19/12/2023 © 2023 | KISTERS...
Need help?
Do you have a question about the HydroMet OSS-B1 and is the answer not in the manual?
Questions and answers