Helwett Packard HPE Aruba Networking 9114 Installation Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

HPE Aruba Networking 9114

Gateway

Installation Guide

Table of Contents

Need help?

Do you have a question about the HPE Aruba Networking 9114 and is the answer not in the manual?

Questions and answers

Summary of Contents for Helwett Packard HPE Aruba Networking 9114

Page 1 HPE Aruba Networking 9114 Gateway Installation Guide...
Page 2 Along with the request, please send a check or money order in the amount of US $10.00 to: Hewlett Packard Enterprise Company Attn: General Counsel WW Corporate Headquarters 1701 E Mossy Oaks Rd Spring, TX 77389 United States of America HPE Aruba Networking 9114 Gateway | Installation Guide 0512273-01 | October 2023...
Page 3: Table Of Contents
Installing and Removing an SFP Module Connecting and Disconnecting an LC Cable Specifications, Safety, and Compliance HPE Aruba Networking 9114 Gateway Specifications Regulatory Model Name Safety and Regulatory Compliance Proper Disposal of HPE Aruba Networking Equipment HPE Aruba Networking 9114 Gateway | Installation Guide...
Page 4: About This Guide
HPE Aruba Networking 9114 Gateway and each of its components. Installation describes how to install the HPE Aruba Networking 9114 Gateway in a number of ways and how to install each of its components. Specifications, Safety, and Compliance lists the HPE Aruba Networking 9114 Gateway's technical specifications and safety and regulatory compliance information.
Page 5: Hpe Aruba Networking 9114 Gateway
HPE Aruba Networking 9114 Gateway HPE Aruba Networking 9114 Gateway The HPE Aruba Networking 9114 Gateway is a high-performance edge appliance with the ability to perform intelligent routing and tunnel orchestration software or wireless control plane management for SASE security and scalability.
Page 6: Power, Status, And Gateway Leds
Table 3: Components of HPE Aruba Networking 9114 Gateway Front Panel Callout Component Description Page Used for basic monitoring of the HPE Aruba page 4 Power LED Networking 9114 Gateway Status LED Gateway LED Reset Configuration button Used to reset the configuration settings...
Page 7: Reset Button
In addition to the LEDs on each port, there are three additional LEDs on the front panel that provides the overall status of the device. These LEDs provide basic monitoring of the overall status of the HPE Aruba Networking 9114 Gateway.
Page 8 Speed status LINK/ACT Link status Green (Solid) Link has been established Green (Blinking) Port is transmitting or receiving data No link on port SPEED Port speed status Green (Solid) 1G speed No link on port HPE Aruba Networking 9114 Gateway |...
Page 9: Rj-45 Console Port
Table 9: Console Terminal Settings Baud Rate Data Bits Parity Stop Bits Flow Control 9600 None None The CONSOLE port is compatible only with RS-232 devices. Non-RS-232 devices, such as APs, are not supported. HPE Aruba Networking 9114 Gateway | Installation Guide...
Page 10: Usb Type-C Console Port
USB Type-C Console Port The HPE Aruba Networking 9114 Gateway has one USB type-C console port that provides console access for direct local access. If both USB and RJ-45 console ports are connected, the USB connection takes precedence over the RJ- 45 console connection.
Page 11: Usb Interface
1G speed 100/10Mbps speed USB Interface There are two USB 3.0 interfaces on the HPE Aruba Networking 9114 Gateway. You can use a USB storage device to save and upload configurations to the gateway. Expansion Slot The expansion slot is reserved for future use. It is compatible with OCP 3.0 SFF supporting PCIE Gen3.0 x16 Lanes.
Page 12: Psu Slot 0
Redundancy With power redundancy, the HPE Aruba Networking 9114 Gateway can continue normal operation even when a power supply fails or is turned off. When multiple power supplies are installed, if one becomes unavailable (fails, or is turned off or removed), the remaining power supplies will attempt to provide full power for the device. If the device’s total power load does not exceed the combined rated output of the remaining and operational power...
Page 13 PSU Slot 1 The HPE Aruba Networking 9114 Gateway includes a PSU slot 1 that has a filler panel covering the opening. PSU slot 1 is for an additional power supply module required for redundancy. PSU slot 1 can hold the same power supply module as PSU slot 0.
Page 14: Installation
Installation Installation This chapter describes how to install a HPE Aruba Networking 9114 Gateway using available mounting options. The gateway ships with an accessory kit that includes the equipment needed to install the gateway in standard, 19-inch telco rack. Additional mounting options are sold separately.
Page 15: Selecting A Location
LEDs. Limited electromagnetic interference For best operation, keep the HPE Aruba Networking 9114 Gateway and all cords and cables at least 0.7 meters (2.3 feet) from fluorescent lighting fixtures, and 2 meters (6.6 feet) from photocopiers, radio transmitters, electric generators, and other sources of strong electromagnetic interference.
Page 16 Gateway. Ensure that you have the correct screws before installing the HPE Aruba Networking 9114 Gateway. Installation Steps To install a HPE Aruba Networking 9114 Gateway into a two-point 19-inch (48.26 cm) Telco rack: Place the mounting bracket over the mounting holes on either side of the gateway (see Figure Secure the bracket to the gateway using the eight screws for the mount bracket (four per bracket) and a suitable screwdriver.
Page 17: Rack Mount Installation - Mid
Rack mount Installation - Mid This mounting option allows mounting the HPE Aruba Networking 9114 Gateway from the middle in standard two- post 19-inch Telco rack. The mounting brackets can be used for this installation as well.
Page 18 Gateway. Ensure that you have the correct screws before installing the HPE Aruba Networking 9114 Gateway. Installation Steps To install a HPE Aruba Networking 9114 Gateway from the middle in a standard two-point 19-inch Telco rack: Place the mounting bracket over the mounting holes on either side of the gateway in the middle (see...
Page 19: Four Post Rack Mount Installation
Aruba Networking 9114 Gateway in four-post racks or cabinets. This rail kit stabilizes and supports the gateway. Optional accessories are available for use withb HPE Aruba Networking 9114 Gateway and are sold separately. Contact your HPE Aruba Networking sales representative for details and assistance.
Page 20 1. Sliders 2. Mounting screw (M4) Install the gateway into the rails. At the front of gateway, secure the sliders and Align the sliders with the rails and slide the gateway HPE Aruba Networking 9114 Gateway | Installation Guide...
Page 21: Installing And Removing A Fan Module
Any one of the three positions may be used. Table or Shelf Installation This mounting option allows the mounting of a HPE Aruba Networking 9114 Gateway on a table or shelf. Required Tools and Equipment Rubber Feet (included in the kit) Installation Steps Attach the rubber feet to the bottom of the gateway.
Page 22: Installing And Removing A Power Supply
The power supply module is hot-swappable when two power supplies are installed. Hot swapping allows you to replace a failed power supply without powering down the HPE Aruba Networking 9114 Gateway during the replacement process. This makes it unnecessary to shut down the HPE Aruba Networking 9114 Gateway during the installation procedure.
Page 23 Figure 11 Installing a Power Supply Module Removing an AC Power Supply To remove the power supply from the HPE Aruba Networking 9114 Gateway: 1. Remove the power cord in the AC connector on the power supply module. 2. Grasping the handle of the failed power supply, release the locking mechanism by squeezing the latch handle while removing the power supply.
Page 24 6. Connect the DC power cords to the DC connector on the power supply module. For more details, see Connecting the DC Power Cord. The DC cable needs to be strain-relieved by tying securely it to a fixed structure or rack. HPE Aruba Networking 9114 Gateway | Installation Guide...
Page 25 Do not remove the DC power supply from the unit with the DC cable installed or the DC source turned Removing a DC Power Supply To remove a DC power supply from your HPE Aruba Networking 9114 Gateway: 1. Ensure that the input circuit breaker is open and the voltage across the power source cables is 0V.
Page 26: Connecting And Disconnecting The Ac Power Cord
Once you have installed the JL085A-AC-PSU, you are ready to power on the device. There is no On/Off switch on the HPE Aruba Networking 9114 Gateway. After connecting the power cord to the power supply module and an AC power outlet, the device powers up.
Page 27: Connecting The Dc Power Cord
Once you have installed the JL757A-DC-PSU, you are ready to power on the device. There is no On/Off switch on the HPE Aruba Networking 9114 Gateway. After connecting the power cord to the power supply module and a DC power outlet, the device powers up.
Page 28: Installing And Removing An Sfp Module
Installing an SFP module To install an SFP module into the HPE Aruba Networking 9114 Gateway, slide the SFP module into a port until a connection is made and an audible click is heard. The SFP module is designed to fit one way.
Page 29 Disconnecting an LC Cable To disconnect an LC fiber optic cable from an SFP module, depress the transceiver handle to release the latch on the cable and simultaneously pull the cable out of the port. HPE Aruba Networking 9114 Gateway |...
Page 30: Specifications, Safety, And Compliance
Chapter 4 Specifications, Safety, and Compliance Specifications, Safety, and Compliance This chapter provides an overview of the HPE Aruba Networking 9114 Gateway specifications, safety, and compliance information. HPE Aruba Networking 9114 Gateway Specifications Physical Device Dimensions (without mounting brackets) (HxWxD): 1.73” x 17.40” x13.82” (4.4 cm x 44.2cm x 35.1 cm) Device Weight: 13.67 lbs (6.2 kg)
Page 31 Select the document that corresponds to your device’s model number as it is indicated on the product label. Use of controls or adjustments of performance or procedures other than those specified in this manual may result in hazardous radiation exposure. HPE Aruba Networking 9114 Gateway |...
Page 32 Mettre au rebut les batteries usagées conformément aux unstruction du fabricant. The battery supplied with this product may contain perchlorate material. Special handling may apply in California and certain other states. See www.dtsc.ca.gov/hazardouswaste/perchlorate for more information. HPE Aruba Networking 9114 Gateway | Installation Guide...
Page 33: Proper Disposal Of Hpe Aruba Networking Equipment
ауданы, Әл-Фараби даңғылы, 77/7, Телефон/факс: +7 727 355 35 50 Proper Disposal of HPE Aruba Networking Equipment HPE Aruba Networking equipment complies with countries' national laws for proper disposal and electronic waste management. Waste of Electrical and Electronic Equipment HPE Aruba Networking 9114 Gateway |...
Page 34 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule II of the Rule. HPE Aruba Networking 9114 Gateway | Installation Guide...
Page 35 China RoHS HPE Aruba Networking products also comply with China environmental declaration requirements and are labeled with the “EFUP 50” label shown at the left. HPE Aruba Networking 9114 Gateway |...
Page 36 Taiwan RoHS Turkey RoHS Turkey RoHS material content declaration Türkiye Cumhuriyeti: AEEE Yönetmeliğine Uygundur. HPE Aruba Networking 9114 Gateway | Installation Guide...