Advertisement
Quick Links
25
26
27
31
32
33
37
38
39
43
44
45
28
29
30
34
35
36
40
41
42
46
47
48
2000W
FLIP OVER SAW
COD2000FLS
MacAllister Power Tools,
1 Hampshire Corporate Park, Chandlers Ford,
Eastleigh, Hants S053 3YX
Technical Helpline 0845 300 2577
C C a a u u t t i i o o n n : Carefully read this entire Instruction Manual before using this product
050707 COD2000FLS ED04
SAFETY AND OPERATING MANUAL
Thank you for purchasing a MacAllister product. We are confident that this product will meet and
exceed your expectations of quality and reliability. Please take the time to carefully read this entire
instruction manual before using your new product, and take note of the basic safety precautions
contained herein.
MacAllister Power Tools,
1 Hampshire Corporate Park, Chandlers Ford,
Eastleigh, Hants S053 3YX
Technical Helpline 0845 300 2577
Advertisement
Related Manuals for MacAllister COD2000FLS
Summary of Contents for MacAllister COD2000FLS
- Page 1 SAFETY AND OPERATING MANUAL Thank you for purchasing a MacAllister product. We are confident that this product will meet and exceed your expectations of quality and reliability. Please take the time to carefully read this entire instruction manual before using your new product, and take note of the basic safety precautions 2000W contained herein.
- Page 2 2 25...
- Page 3 Contents Parts list II - Technical data III - Safety instructions IV - Getting started V - Operation VI - Maintenance VII - Guarantee II - Technical data I - Parts list Saw table Voltage:....... 230-240V~50Hz Bevel position locking lever Rated input:.............
- Page 4 III - Safety instructions plugging in power tools that have the switch on GENERAL SAFETY INSTRUCTIONS invites accidents. WARNING! Read all instructions. Failure to follow all d) Remove any adjusting key or wrench before instructions listed below may result in electric shock, fire turning the power tool on.
- Page 5 ADDITIONAL SAFETY RULES FOR FLIP OVER SAWS is free from obstruction. WARNING! Rotating Circular Saw Blades are extremely Repeat this procedure at all maximum mitre and bevel dangerous and can cause serious injury and amputation. positions before commencing operation of the Mitre Saw. Always keep fingers and hands at least 6"...
- Page 6 Approved ear protection should be worn when using flip over saws. Never try to cut pieces that are larger than the maximum specified for the machine, it can cause damage to the blade guard and could cause injury to the operator. The equipment is intended for use only in premises having a service current capacity equal to, or greater than 100A per phase.
- Page 7 IV - Getting started Loosen the riving knife locking knob and relocate the riving knife in the storage position shown inPic.8. Raise the saw blade fully using the blade height adjustment knob. ACCESSORIES The flip over saw is supplied with the following accessories: Attach the chip collection case to the table and •...
- Page 8 square does not touch the teeth on the blade as a should be 45° from the vertical position or 135° false reading may occur due to the thickness of from the table. If adjustment is required proceed the tungsten carbide tip. as follows: If adjustment is required proceed as follows.
- Page 9 Remove the chip collection case from the table using the degree scale. (using the supplied hex key press the securing When the desired angle has been set, tighten the screw in, then rotate 90º). Using the blade height locking lever. adjustment knob fully lower the blade then loosen NOTE: The degree scale is a guide only, for the riving knife locking knob and relocate the riving...
- Page 10 29, 30 & 31 CROSS CUTTING MITRE AND ANGLE CUTS Cross cutting is cutting wood across the grain at Loosen the rotating table locking lever then lift up 90° or square with both the edge and the flat side the locking knob and rotate the table to the of the wood.
- Page 11 The safe way to perform repetitive cutting, is to set Re-check all adjustments and settings periodically the rip fence to give the required length, and to be for accuracy. clear of the front of the blade. When the cut is WARNING: It is important that the blade guard is made, the end of the work piece is clear of the rip fitted and operates correctly.
- Page 12 VII - Guarantee Thank you for investing in MacAllister. These products have been made to demanding, high quality standards and are guaranteed for domestic use against manufacturing faults for a period of 36 months from the date of purchase.
Need help?
Do you have a question about the COD2000FLS and is the answer not in the manual?
Questions and answers