Advertisement
Technical Specifications unas s00
20 Hz~ 20 kHz continuous power output
both channels driven
1 kHz continuous power output
both channels drivan (THD: 1%}
2 * 85 W (8 2)
2*
95 WO)
2
135 Wa
83 Hz~ 12.5 kHz continuous power output
both channels driven (0.7 %)
2
85W (80)
2 * 120 W (4G)
Total harmonic distortion (Power Amp Direct input} —
rated power at 20 Hz~20 kHz
0.005 % (8 GQ)
rated power at 1 kHz
9.0009 % (8 D}
0.002 % {4 2)
half power at 20
Hz~ 20 kHz
0.005 % (8 ©)
half power at 1 kHz
0.0009 % (8 G)}
0.002 % (4 Q)
Intermodutation distortion
rated power at 50 Hz: 7 kHz= 4:1, SMPTE, 8 ©
Residual hum and noise
Damping factor
Headphones output level and impedance
Load impedance
0.007 %
0.2 mV
60 (8 Q), 30 (4 29)
650 mvV/330
AorsB
4Q~162
Aand B
8Q~16 0
Input sensitivity and impedance
ee
PHONO MM
2.5 mVI47 kQ
PHONO MC
170 pVv/220
TUNER, CD, AUX, TAPE 1, TAPE 2/DAT
150 mV/22 kO
POWER AMP DIRECT
1VNB ko
Phono maximum input voltage (IHF '86, 1 kHz, RMS)
Mia
170 mv
MC
12 mv¥
SIN
rated power (4 ©)
PHONO
MM
79 dB (IHF '66: 86 dB)
PHONO
MC
67 dB (iHF '66: 68 dB, 250 pV)
TUNER, CD, AUX, TAPE 1, TAPE 2/DAT
97 dB UHF "66: 100 dB)
POWER
AMP
DIRECT
106 dB UHF "66: 115 dB}
—26 dB power (4 ©)
PHONO
MM
77 dB
PHONO
MC
67 dB
TUNER, CD, AUX, TAPE 1, TAPE 2/DAT
84 dB
30 mW power (4 0}
PHONO
MM
75 dB
PHONO
MC
67 dB
TUNER, CD, AUX, TAPE 1, TAPE 2/DAT
78 dB
Protection Circuitry
The protection circuitry may have operated if either of the foliow-
ing conditions ts noticed:
® No sound is heard when the power is switched ON.
(The current drive indicator of the operation
indicator is not
illuminated.)
* Sound stops during a performance.
The function of this circuitry is to prevent circultry damage if. for
avamnia
tha
nnsitive
ana
nanatiuem
sanoaoslbar
Anne
AAtAR
UWuirae
awe
WAS,
LEIS
PIS
Gl
IO YalIeo
OPENS!
UME
ISTO
wifSs
aig
"shorted", if speaker systems with an Impedance less than the
ef oe
Frequency response
PHONO
RIAA Standard curve
$0.8 dB (360 Hz~15 kHz)
TUNER, CD, AUX, TAPE 1, TAPE 2/DAT
2H? ~ 100
bety
f— 2 Aaa
amt
Ss
rer
AT rae |
en
+0 dB, —0.2 dB (20 Hz~20 kHz)
2 Hz~120 kHz (—3 4B)
+0 dB, —0.2 dB (20 Hz~20 kHz}
POWER AMP DIRECT
Tone controts —
BASS
50
Hz, +10 dB, -10 dB
TREBLE
26 kHz, +710 dB, —10 dB
Loudness control (volume at — 30 d8)
50 Hz, +9 dB
Output voltage
TAPE 1, TAPE 2/DAT, REC OUT
150 mV
Channel balance, AUX 250 Hz~ 6,300 Hz
+148
Channel separation, AUX 1 kHz
§9 dB
@ GENERAL
Power consumption
540 W
Power supply
Almanelnwe
FA
we Bw
Ty
>
"3
Sree cee
EE eS Le
ag
AC 50 Hz/6G Hz. 240 V
420 ¥ 1528»
275 mm
{16-*5/16" * G-7/32" x 14-9/18"}
Weight
115 kg (25.4 Ib}
Notes:
1. Specifications are subject to change without notice.
Weight and dimensions are approximete.
2. Total harmonic distortion Is measured by the digital spectrum
analyzer.
indicated
rated
impedance
of this unit are used, or if DC
voltage appears in the output
lf this occurs, follow the procedure outlined below:
1. Switch OFF the power.
2. Determine the cause of the problem and correct it
3. Switch ON the power once again
Note:
Ak. mw
Oh.
SRLS
Ld
A
8, ihe unit wii not operate
ions,
OFF and then ON again.
ultry functi
switched
q U
Advertisement
