Philips 51PP9303H Directions For Use Manual page 9

T
he TV's audio/video (AV) input jacks provide
for direct picture and sound connections
between the TV and accessory devices such as
VCRs, DVD players, and others that have AV out-
put jacks.
This example, which uses the INPUT-AV 1 jacks,
shows you one way you can connect a VCR to
your TV.
Refer to the directions-for-use manual for your
VCR for further information on connections.
To make the connections shown in this example,
you will need:
• one coaxial cable (75 )
• one cable for a video connection (standard
RCA-type phono plug)
• two cables for audio connections (standard
RCA-type phono plugs) (only one cable is
needed for a nonstereo VCR).
NOTE: The cables are not supplied with your TV.
You should be able to buy them at most stores
that sell electronics. Or you can call our
Customer Care Center at 1-800-531-0039
1
Connect a cable TV or antenna signal to
the ANT IN jack on the back of the VCR.
2
Connect from the OUT jack on the
back of the VCR to the ANTENNA IN
75 jack on the back of the TV.
3
Connect the VIDEO OUT jack on the
back of the VCR to the INPUT-AV 2
VIDEO jack on the back of the TV.
4
Connect the audio output R(ight) and
L(eft) jacks on the back of the VCR to
the INPUT-AV 2 AUDIO jacks on the
back of the TV.
NOTE: If the VCR is a mono (nonstereo)
unit, connect only the left audio cable,
which usually has a white-coded plug.
5
Press the AV button on the remote con-
trol as many times as necessary to select
the AV2 source for viewing of materials
from the VCR.
C
ONNECTING A
3
2
ANTENNA IN 75
Rear of VCR*
* (Example: Philips VCR
model VR674CAT)
AV1
POWER
TV VCR ACC
ACTIVE
SWAP PIP CH CONTROL FREEZE
DN UP
SOUND PICTURE
STATUS/
EXIT
MUTE
VOL
1 2 3
4 5 6
7 8 9
TV/VCR
0
A/CH
SURF
5
SURF PIP ON/OFF
REC • FORMAT SLEEP
SAP
AV DOLBY V PROG.LIST
ITR/ HOME HOME PERSONAL
RECORD VIDEO MOVIES
POSITION PIP
9
Connecting Accessory Devices to Your TV
VCR
Rear of TV
DVI
4
INPUT-AV 1 OUTPUT INPUT-AV 2
Y
VIDEO
VIDEO
S-VIDEO
S-VIDEO
L
Pb
L
L L
AUDIO AUDIO
Pr
R R
• Stereo sound will pass from the ANT
OUT jack on the VCR to the ANTENNA
IN 75 jack on the TV only when the
VCR is in TV mode. This is the mode
that allows the TV to use its channel
selector.
• To simplify making connections, audio
and video cables often have color-coded
plugs. The jacks on your TV are likewise
color coded to match the plugs. The cod-
ing is as follows:
—Yellow for video (composite)
—Red for the right audio channel
MENU/
SELECT
—White for the left audio channel
NOTE: If your VCR is mono (non-
stereo), you will connect only one audio
CH
cable. You must ensure that the TV is set
to MONO for the signal source to which
you've connected the VCR (INPUT-AV 2,
INPUT-AV 1, or the side panel inputs
[AV3]). Otherwise, you will receive
sound from only one of the TV's speakers.
See page 36.
c c C
You can display the AV1, AV2, or AV3 signal
sources in the PIP window. See page 7 of the
Quick Use and Setup Guide for information on
using the Picture-in-Picture (PIP) feature.
HD INPUT-AV 5
HD INPUT-AV 4
G/Y
R/Pr
B/Pb
V
L L Coaxial Cable
SYNC
AUDIO
AUDIO Lead-in from
H
Cable TV Company
R R
or VHF/UHF Antenna
1
AUDIO
L
ANT
IN
IN
R
VIDEO
OUT
IN
OUT CH3 CH4
H H
ELPFUL INTS
I O
HECK T UT