Table of Contents
Advertisement
Before calling Service
Ambient temperature
Do not hang up the monitor above a
central heating or other heating sources.
If the power/standby indicator in front is
red and blinking, the temperature inside
the monitor has become too high and has
activated the protector.The monitor will
be turned off. Unplug the power cord and
wait for the monitor to cool down.
Care of the screen
Clean the anti-reflex coated flat glass
screen with a slightly damp soft cloth. Do
not use abrasives solvents as it can
damage the glass surface of the screen.
Plasma Display characteristics
Caution: A video source (such as a video
game, DVD, or video information channel)
which shows a constant non-moving
pattern on the monitor, can cause damage
to the screen.When your Flat-Monitor is
continuously used with such a source, the
pattern of the non-moving portion of the
game (DVD, etc.) could leave an image
permanently on the screen.When not in
use, turn the video source
OFF
To prevent or to reduce burn-in of the
screen, select a
setting in the
LONG LIFE
menu. See p. 8.
OPTIONS1
Very incidentally and after a longer period
of unuse (approx. 1 year) the screen may
display some strange colour deficiencies.
This is quite normal for plasma displays
and these effects will disappear after the
set has been turned on for some time.
A plasma display consists of more than 1,2
Million colour pixels. It is within industry
standards that very few pixels (< 0.001%)
may be defective, even for a new set.
There is however no reason to doubt
about the quality of the set.
The plasma display technology operates
with rare gases which are being influenced
by air pressure. Up to an altitude of
2000m above sea-level (local air pressure
equal or above 800 hPa), the display is
functioning fine. Operating the set at a
higher altitude (lower air pressure), the
picture becomes unstable and the picture
performance is deteriorating.
Before calling Service
12
The plasma display might then also
produce a humming sound. After bringing
the set below 2000 m (local air pressure
equal or above 800 hPa) it works fine
again.Transportation has no influence.
Control of peripheral equipment
The infrared radiation of the screen may
influence the reception sensitivity of other
peripherals. Solution: replace the batteries
of the remote control or change position
of other equipment. E.g. keep away a
wireless headphone from within a radius
of 1,5 m.
No stable or not synchronised VGA
picture
Check if you have selected the correct
display mode in your PC. See Table of
Signal Supported.
No picture
Are the supplied cables connected
properly? (The power cable to the display,
the VGA cables,...)
Is your PC switched on?
Do you see a black screen and the
.
indicator in front of the monitor lights up
green, this means that the display mode is
not supported.
Switch your VGA source to a correct
mode.
Remote control
If your monitor no longer responds to the
remote control, the batteries may be
exhausted.
If your problem is not solved:
Switch your monitor off and then on
again.
Never attempt to repair a defective
monitor yourself.
Check with your dealer or call a video
technician.
Transport
Keep the original packaging to transport the
monitor if needed.
End of life directives
Philips is paying a lot of attention to
produce environmentally-friendly in green
focal areas.Your new monitor contains
materials which can be recycled and
reused.
At the end of its life specialised companies
can dismantle the discarded monitor to
concentrate the reusable materials and to
minimise the amount of materials to be
disposed of.
Please ensure you dispose of your old
monitor according to local regulations.
How to dispose of batteries ?
The batteries supplied do not contain the
heavy metals mercury and cadmium.
Nevertheless in many countries batteries
may not be disposed of with your
household waste. Please ensure you dispose
of batteries according to local regulations.
Miscellaneous
. Ambient temperature: + 5~ + 40°C
. Maximum operating altitude:
2000 m/6526 ft
(min. air pressure 800hPa)
. Mains: AC 100-240V
. Standby consumption: 1 W
. Weight (excl. packaging)
Display: 46 kg
. Dimensions (wxhxd):
Display: 124,2 x 76,7 x 11 inch
. Wall mounting bracket included
Settings are out of adjustment
Select
in the
RESET
OPTIONS 1
to restore the predefined factory settings.
menu, p. 8
Advertisement
Table of Contents
