17" LCD Open frame SAW TM ( t he Primary Type ) U ser Guide (Rev2.0) Table of Contents Chapter 1 Introduction 1.1 Product Description ...........................3 1.2 Precautions ..............................3 1.3 About the Product ............................3 Chapter 2 Installation and Setup 2.1 Unpacking Your Touchmonitor ........................4 2.2 Product Overview ............................5 2.3 Attaching the L-bracket …………………………………………………………………………...……..5 2.4 VESA Mounting Interface………………………………………………………………………………..6...
Chapter INTRODUCTION 1.1 Product Description Keetouch’s 17" open frame LCD touchmonitors have a long-lasting product cycle because the enclosure is controlled by Keetouch’s specifications. Future panel improvements are therefore possible without external changes. The KOT-0170US-SA4B integrate with the Keetouch’s SAW technology touchscreen.
17" LCD Open frame SAW TM ( t he Primary Type ) U ser Guide (Rev2.0) Chapter INSTALLATION AND SETUP This chapter discusses how to install your LCD touchmonitor and how to install the driver software. 2.1 Unpacking Your Touchmonitor Check that the following 9 items are present and in good condition: One Touchmonitor Two L-brackets...
17" LCD Open frame SAW TM ( t he Primary Type ) U ser Guide (Rev2.0) One Power cable US/Canada One European power cable 2.2 Product Overview Main Unit Rear View Side View Bottom View 2.3 Attaching the L-Brackets NOTE: You will need a screwdriver to attach the L-brackets. To attach the L-brackets: 1 Lay the monitor face down.
17" LCD Open frame SAW TM ( t he Primary Type ) U ser Guide (Rev2.0) Option 1 (L-brackets to the left and right sides) Option 2 (L-brackets to the up and down sides) 2.4 VESA Mounting Interface Your touchmonitor conforms to the VESA Flat Panel Monitor Physical Mounting Interface (FPMPMITM) Standard which defines a physical mounting interface for flat panel monitors, and corresponding standards for flat panel monitor mounting devices, such as wall and table arms.
17" LCD Open frame SAW TM ( t he Primary Type ) U ser Guide (Rev2.0) NOTE:Do not penitrate the M4 screw into the monitor more than 5mm. 2.5 Interface Connection Note: Before connecting the cables to your touchmonitor and PC, be sure that the computer and touchmonitor are turned off.
Depending upon whether you connected the USB communication cable or the Serial(RS232) communication cable, you should install only the USB driver or the Serial(RS232) driver. Install the USB driver, please chose the “KeeTouch, KCA USB Series, USB”;Install the Serial(RS232) driver, please chose “theKeeTouch,KCA RS232 Series,Serial”.
17" LCD Open frame SAW TM ( t he Primary Type ) U ser Guide (Rev2.0) After selecting the proper interface, click the Install button to start installing the driver as following. Installation successfully as following: 2.6.2 Calibration Click at the right side in the down corner of the Desk-Top,then choose “calibrate”in the pop-out of the menu ,and choose the “RS232”...
Page 10
17" LCD Open frame SAW TM ( t he Primary Type ) U ser Guide (Rev2.0) Windows will pop-out the calibration interface, then click “+” with finger one by one, as follow: After clicking the “+” on by one, the calibration is completed. - 10 -...
17" LCD Open frame SAW TM ( t he Primary Type ) U ser Guide (Rev2.0) Chapter OPERATION 3.1 About Touchmonitor Adjustments Your touchmonitor will not likely require adjustment. Variations in video output and application mayrequire adjustments to your touchmonitor to optimize the quality of the display.For best performance, your touchmonitor should be operating in native resolution, that is 1280×1024 at 80k-75 Hz.
17" LCD Open frame SAW TM ( t he Primary Type ) U ser Guide (Rev2.0) 2)Decrease value of the adjustment item. 3)Select item clockwise. 6 Menu Display/exits the On Screen Display (OSD) menus 3.2 Controls and Adjustment 3.2.1 On Screen Display (OSD) Menu Functions To Display and Select the OSD Functions: 1 Press the Menu key to activate the OSD menu.
17" LCD Open frame SAW TM ( t he Primary Type ) U ser Guide (Rev2.0) Chapter TROUBLESHOOTING If you are experiencing trouble with your touchmonitor, refer to the following table. If the problem persists, please contact your local dealer or our service center. Solutions to Common Problems Problem Suggestion(s)
17" LCD Open frame SAW TM ( t he Primary Type ) U ser Guide (Rev2.0) Appendix NATIVE RESOLUTION The native resolution of a monitor is the resolution level at which the LCD panel is designed to perform best. For the LCD touchmonitor, the native resolution is 1280 x 1024 for the 17 inch size.In almost all cases, screen images look best when viewed at their native resolution.
17" LCD Open frame SAW TM ( t he Primary Type ) U ser Guide (Rev2.0) Appendix TOUCHMONITOR SAFETY This manual contains information that is important for the proper setup and maintenance of your touchmonitor. Before setting up and powering on your new touchmonitor, read through this manual, especially Chapter 2 (Installation), and Chapter 3 (Operation).
17" LCD Open frame SAW TM ( t he Primary Type ) U ser Guide (Rev2.0) Appendix TECHNICAL SPECIFICATIONS Model No. KOT-0170US-SA4B Series Structure Metal-cased open frame LCD Type " A ctive matrix TFT-LCD Active Area 13.3 " ( 338mm)×10.6 "...