Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Protocol SAW70
Summary of Contents for Protocol SAW70
- Page 1 42579 SAW70 70" / 500 LB CAPACITY LIGHTWEIGHT ALUMINUM SAWHORSE PRODUCT MANUAL SCAN TO WATCH PRODUCT ASSEMBLY VIDEO CAUTION: To reduce the risk of injury, user must read and understand this product manual. Save these instructions for future reference. P RO T OC OL EQUI PM ENT.CO M...
-
Page 3: Table Of Contents
TABLE OF CONTENTS Features and Specifcations ........................3 Preparing the Sawhorse..........................4-5 Installing the Tough Top..........................6 Extending the Chassis..........................7 Transporting and Storing the Sawhorse ...................8-9 Safety and Warnings........................... 10 General Maintenance..........................10 Warranty ................................11 WARNING: Be sure to read and understand all safety instructions in this manual, including all safety alert symbols such as “DANGER”, “WARNING”, “CAUTION”, and “IMPORTANT”... -
Page 4: Preparing The Sawhorse
PREPARING THE SAWHORSE Place sawhorse on a flat and level surface with folded legs facing up. Turn leg lock handle counterclockwise and unfold first set of legs from chassis. CROSS BRACE Deploy first set of legs. Make sure cross brace is secured in place to ensure legs are fully opened. - Page 5 PREPARING THE SAWHORSE After both sets of legs are deployed, lift sawhorse in an upright position. Ensure sawhorse is stable and both sets of legs are fully opened. FIND OUT MORE AT PROTOCOLEQUIPMENT.COM...
-
Page 6: Installing The Tough Top
INSTALLING THE TOUGH TOP Tools Required: PH2 screwdriver (not included) CROSS BRACE SCREW INNER CROSS BRACES Place tough top on chassis. Position tough top so that it is horizontally centered. Short sides of the top should align with edges of inner cross braces. Secure tough top using a PH2 screwdriver to install screws from underneath the cross braces, two screws per cross brace. -
Page 7: Extending The Chassis
EXTENDING THE CHASSIS Turn to loosen all four paddle knobs located within chassis. IMPORTANT: Do not loosen knobs too much as they may disengage. CROSS BRACES Locate cross braces on chassis frame – two on each side. Use one hand to grab inner frame cross brace (underneath tough top) to keep chassis steady. Use other hand to grab outer frame cross brace and pull outward to extend chassis. -
Page 8: Transporting And Storing The Sawhorse
TRANSPORTING AND STORING THE SAWHORSE If chassis is expanded, turn to loosen all four paddle knobs located within chassis. Collapse chassis and tighten all four paddle knobs to lock chassis in place. IMPORTANT: Do not loosen knobs too much as they may disengage, and do not overtighten. CROSS BRACE LEG LOCK LEGS OPPOSITE... - Page 9 TRANSPORTING AND STORING THE SAWHORSE Turn leg lock to secure legs in place. HANDLE WHEELS Use handles with built-in wheels on either side of chassis to transport sawhorse to desired location. FIND OUT MORE AT PROTOCOLEQUIPMENT.COM...
-
Page 10: Safety And Warnings
SAFETY AND WARNINGS SAFETY INSTRUCTIONS FOR SAWHORSES Use caution when folding or unfolding legs to limit any finger pinch points. Place sawhorse on flat and level surface to keep from rocking or tipping. Do not exceed the rated capacity on main frame table/chassis. Ensure load is equally distributed. -
Page 11: Warranty
WARRANTY 3-YEAR LIMITED WARRANTY This product is backed by a 3-year limited warranty. This warranty covers manufacturer defects and workmanship. The warranty excludes misuse or abuse and normal wear and tear. This warranty gives you specifc legal rights, and you may have other rights, which vary from state to state. - Page 12 02.17.2023 JS PRODUCTS • 6445 MONTESSOURI STREET • LAS VEGAS, NV 89113 CUSTOMER SERVICE: 1-877-707-6449 • PROTOCOLEQUIPMENT.COM...
Need help?
Do you have a question about the SAW70 and is the answer not in the manual?
Questions and answers