Download Print this page

Sanuvox BIOSMART SCREEN Instruction Manual

Touch screen for bio-wall
Hide thumbs Also See for BIOSMART SCREEN:

Advertisement

Quick Links

REGISTER
YOUR WARRANTY
READ AND SAVE THESE SAFETY INSTRUCTIONS BEFORE USING THIS PRODUCT.
Read and follow all instructions contained in the manual before using the product. Read the maintenance instructions before opening the UV unit
or system. Failure to comply with these instructions may result in injuries or damage to the UV unit or system.
1.
Installation and servicing of UV units or systems (in an
air conditioning system or not) can be hazardous. Only
trained and qualified service personnel should install,
repair or service equipment.
2.
Untrained personnel can perform basic maintenance
functions such as replacing lamp(s) and/or filter(s). All
other operations should be performed by trained service
personnel.
3.
The unit is not to be used by persons (including children)
with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge.
CAUTION: Unit is not a toy. Keep away from
unsupervised children. Do not leave children unattended
with the unit.
4.
DO NOT hang onto the UV unit or system.
5.
Some UV units or systems could be heavy: Make sure
you have a minimum of 2 people to safely move or install
these UV units or systems, and make sure you adopt the
most ergonomic position possible (use UV unit or system
handles, if applicable).
CAUTION: Installing or maintaining heavy equipment,
especially overhead, can cause back pain or other injuries.
6.
When installing or servicing an overhead UV unit or system,
be careful not to fall off the stepladder. Furthermore, make
sure the UV unit or system latches are always in place to
prevent falling parts.
CAUTION: Some parts of some UV units and systems
may open suddenly if the UV unit or system is installed
high up without its locks.
6.1.THIS AIR CLEANER SHALL NOT BE INSTALLED ON THE
HOT-AIR SIDE OF DUCT-TYPE SYSTEMS.
Installation Date: _______________
Installer Contact Info.: _________________________________________
BIOSMART SCREEN
TOUCH SCREEN FOR BIO-WALL™
Commercial Model

IMPORTANT SAFETY INSTRUCTIONS

NEVER EXPOSE EYES OR SKIN TO AN OPERATING UV LAMP.
7.
Units that are obviously damaged must not be operated.
8.
CAUTION: When working on the UV unit or system,
observe precautions on the literature, tags and labels
attached to the UV unit or system, and all other safety
precautions considered as best practices in the HVAC
industry, if applicable.
9.
When applicable, local regulation may comprise more
restrictive installation and/or certification requirements.
The aforementioned requirements prevail on those of this
document and the installer agree to conform to these at his
own expense.
10. Follow all the safety instructions outlined in this document
and respect all local and national codes applicable.
11. All UV units or systems contain a UV-C source. Damage to
the housing or unintended use of the UV unit or system may
result in harmful UV-C leaks. UV-C may, even in little doses,
cause harm to the eyes and skin.
12. Never expose eyes or skin to an operating UV lamp.
Therefore, before installing or performing maintenance
on the UV unit or system, TURN OFF AND DISCONNECT
the UV unit or system from all power sources (there
may be more than one switch to disconnect) and also
disconnect the HVAC system, is applicable.
CAUTION: Electrical shock may cause injuries or
possibly death. FIRST AID INSTRUCTIONS: If injured,
consult a doctor.
13. UV rays may damage certain types of filters (polymer or
plastic); please keep the UV unit or system light away from
shining directly on plastic.
Sanuvox Technologies Inc, © 2019 All rights reserved. September 2023 EN v.1.1
14. When installing or performing maintenance on the UV unit
or system, it is recommended to wear safety gloves. In
order to avoid reduced performance of lamp(s), do not
touch lamp glass without gloves.
15. Just like conventional fluorescent lamps, UV lamps contain
a small quantity of mercury: if a lamp breaks, clean and
dispose of with care. UV lamps can be disposed/recycled
after use in the same way as any other fluorescent lamps.
Contact and follow the specific instructions of your local
and national authorities.
15.1. Dispose of unit or system according to the specific
instructions and standards of your local and national
authorities.
16. Use only specified SANUVOX branded replacement
UV lamps for your UV unit or system. Use of any other
lamps will void your warranty and can result in damage to
the UV unit or system.
17. Sanuvox UV units or systems are not waterproof. DO NOT
INSTALL OUTDOORS OR IN WET LOCATION unless
specified otherwise.
18. Use of this unit or system supplements, but does not
replace, infection control best practices. Users must follow
all these practices, particularly with regard to cleaning and
disinfecting surfaces.
For any inquiries on a UV unit or system, contact :
Installed by: _________________
Instruction Manual
SAVE THESE INSTRUCTIONS
Robert Smith
146 Barr St, Saint-Laurent
Quebec, CA, H4T 1Y4
1-888-726-8869
techsupport@sanuvox.com

Advertisement

loading

Summary of Contents for Sanuvox BIOSMART SCREEN

  • Page 1: Important Safety Instructions

    6.1.THIS AIR CLEANER SHALL NOT BE INSTALLED ON THE Quebec, CA, H4T 1Y4 HOT-AIR SIDE OF DUCT-TYPE SYSTEMS. 1-888-726-8869 techsupport@sanuvox.com Installation Date: _______________ Installed by: _________________ Installer Contact Info.: _________________________________________ Sanuvox Technologies Inc, © 2019 All rights reserved. September 2023 EN v.1.1...
  • Page 2: Table Of Contents

    Instruction Manual for BioSmart Screen TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS TABLE OF CONTENTS ABOUT THE PRODUCT SETUP & INSTALLATION What you will need What’s included Setup Step by Step Installation OPERATION How to Operate your Product MAINTENANCE How to Clean your Product...
  • Page 3: About The Product

    The BioSmart Screen, a 5 VDC power supply module, a 20' Ethernet cable and a grommet. Setup When selecting the appropriate location for your BioSmart Screen, ensure that it can be supplied with the necessary current (100-240V @ 50-60Hz). The 5 VDC power supply must be plugged into a conventional power outlet.
  • Page 4: Step By Step Installation

    9. Connect the other end of the Ethernet cable to the Ethernet port on the display. 10. Finally, plug the power supply into a conventional power outlet, plugging the DC cable into the BioSmart Screen’s power port. Your BioSmart Screen is now ready to operate. www.sanuvox.com...
  • Page 5: Operation

    How to Operate your Product The BioSmart Screen is designed to give you real-time information about the status of the lamps in your BIO-WALL™. CAUTION: The recommended operating temperature is between 4 to 40°C (40 to 105°F). Using the BioSmart Screen outside of this temperature range may reduce its performance.
  • Page 6: Maintenance

    (DNA/RNA) of microorganisms, which inactivates them. Unlike conventional UV lamps on the market, Sanuvox units and systems use a patented process that delivers a maximum dose of UV to the moving air stream or surfaces. CAUTION: Never expose eyes or skin to an operating UV lamp.
  • Page 7: Warranty

    This warranty applies only to the original purchaser of this product from the original date of purchase. At its option, SANUVOX will repair or replace this product if it is found to be defective in material or workmanship.