Cooper Lighting ALL-PRO MSLED180W Instruction Manual

MSLED180 (Black)
MSLED180W (White)
ENGLISH
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
HOW IT WORKS
During the daylight hours, the solar panel turns the sunlight
into energy that is stored in the rechargeable battery pack.
Your light features a motion sensor that turns the light ON
at night when motion is detected. This light is equipped
with a photocell, which only allows the fixture to turn ON
during the nighttime hours.
WARNINGS AND CAUTIONS
INSTRUCTIONS PERTAINING TO A RISK OF FIRE OR INJURY TO PERSONS.
To reduce the risk of fire or injury to persons, read and follow these instructions:
• DO NOT replace batteries.
• DO NOT dispose of this product in fire. Batteries inside this product may explode or leak.
• DO NOT puncture this battery pack. DO NOT work on this battery pack
• DO NOT disassemble fixture. The fixture does not have any user serviceable parts.
• For outdoor use only.
• Lithium-Ion batteries must be disposed of in accordance with local waste ordinances and
regulations.
• Do not operate a luminaire with a missing or damaged lens.
• Fixture is suitable for wall mount only. NOT suitable for ground mount installation.
• Do not cut the solar panel wire. Discontinue use if the wire becomes frayed or broken.
SAVE THESE INSTRUCTIONS.
FOR BEST RESULTS
• Allow fixture to receive four full days of sunlight before turning fixture ON.
• Locate solar panel in an area that will receive the
maximum amount of sunlight during the daylight
hours. Locate panel to receive at least 3-4 hours of
direct sunlight daily.
• Test your charged unit before permanently installing.
• Install the motion sensor 8-12 feet above the ground.
(Motion sensor is less sensitive above 12 feet.)
• Locate motion sensor so motion moves across the
detection zone (Fig. 1).
• Locate sensor away from heat producing sources to
prevent false triggering. Also be very careful not to
include objects such as windows, white walls and
water in the detection zone.
Questions?/ ¿Preguntas? 1-800-334-6871 ConsumerProducts@ cooperlighting .com
PACKAGING CONTENTS/ CONTENIDO DEL PAQUETE
A. Light fixture with 12 in. lead wire connector
Accesorio para la luz con conector de cable de 12 pulg
(Single head position) (Twin head position)
(Posición de cabezal simple) (Posición de cabezal doble)
180 degrees
Fig. 1
B. Solar panel with 15 ft. cord
Panel solar con cable de 15 pies
D. (4) Solar panel mounting
screws
(4) Tornillos de montaje
del panel solar
• Locate sensor away from moving objects such as
trees, large shrubs and street traffic.
• You will need to adjust the angle of the solar panel
throughout the year as seasons change in order to
keep it at the best possible angle to the sun.
• Keep solar panel clear of any objects that will block
Up to
the sunlight. It will be necessary to periodically clean
70 feet
the solar panel with soft wet cloth.
• During periods of several cloudy days, the battery
may fall below the operating level and will need to be
recharged with sunlight.
MOUNTING YOUR FIXTURE
1. Locate area in which you would like to install your
light fixture.
NOTE: For fixture to operate properly, the solar panel (B)
must be located in an area that will receive the maximum
amount of sunlight and is free from obstructions.
2. Using the fixture mounting screws (C) provided,
mount fixture (A) to a solid surface 8-12 feet above
the ground by placing the screws through the holes
on either side of the fixture (Fig. 2). Adjust sensor
head so that control switches are facing the ground.
Remove label from the front of the sensor head.
3. Using the solar panel mounting screws (D) provided,
mount solar panel (B) to a solid surface (Fig. 3).
Adjust the angle of the solar panel (B) so that it will
receive the maximum amount of direct sunlight
during the daylight hours.
NOTE: For best results, locate panel to receive at least
3-4 hours of direct sunlight daily.
4. Carefully route the wire from the solar panel (B)
to the fixture (A) and plug it into the connector
extending from the side of the fixture housing (A)
(Fig. 4). Make sure to push the connector plugs
tightly together until you hear two clicks to ensure
they are fully engaged.
OPERATING YOUR FIXTURE
NOTE: Make sure you allow fixture to receive four full
days of sunlight before turning fixture ON.
1. Move slide switch on bottom of the sensor
to "TEST" (Fig. 5).
NOTE: Fixture has a warm up period of about one
minute. Light will turn on during this period. Once the
light turns off, you are ready to test.
1
Instruction Manual/ Instrucciones
C. (2) Fixture mounting screws
(2) Tornillos de montaje
del accesorio
Fig. 2
C
Fig. 3
D
B
D
Fig. 4
A
Fig. 5
A
C
D
D
B
A