CE Tech 5053-WH Instruction And Installation Sheet

MADE IN CHINA
HECHO EN CHINA
DISTRIBUTED BY
DISTRIBUIDO POR
HOME DEPOT U.S.A., INC.
2455 PACES FERRY RD., N.W.
ATLANTA, GA 30339
Use CE Tech's TV Multimedia Recessed Box to install low voltage cables behind your HDTV or other display device. The TV Multimedia Box is also
designed to be used with flexible tubing.
IMPORTATN INSTRUCTIONS:
This product is designed for retrofit work only because the old workbox cannot be attached to a stud.
WARNING:
Before installing this product, be sure the power is off by switching the circuit breaker to off or removing the fuse(s). Test the power to make
sure the power is off. Be sure to instlal the Recessed Box in accordance with the National Electrical Code (NEC) and local codes.
Fig. 2
Installation Instructions:
Fig. 1: Cut out the supplied template from page 3 of this instruction sheet. Place the template on the wall in the desired install location. Using your pen
or pencil, trace the template on the wall. Then use a drywall saw or utility knife to cut a hole in the drywall the size of the template. See Figure 1 before
tracing your opening. Remember, this wall plate is designed to be installed between the studs. It cannot be installed on top of a stud.
Fig. 2: Run the source of power to the included Old Work Electrical Box. Be sure to follow all local electrical codes.
Fig. 3: Connect a décora style duplex receptacle (sold separately) to a piece of 14/2 wth ground UL approved electrical building wire (not included)
following the instruction sheet included with the electrical receptacle. Once you have wired the receptacle, screw it into the Old Work Electrical Box until
the receptacle is firmly secured as shown in Fig. 3.
Fig. 4: Use the four provided screws to secure the Old Work Electrical Box and receptacle to the mounting studs on the backside of the TV Multimedia
Recessed Box.
Fig. 5: Before installing the TV Multimedia Recessed Box into the wall opening, make sure to pull your low voltage cables through the top and bottom
openings or the side opening.
If you are using flexible tubing, cut out either the 1" or 2" knockout (depending on your flexible tube hole size) from the snap-in cover plate, now run your
cables through the snap-in plate opening, then attach your flexible tubing to the snap-in cover and then snap the snap-in cover into the 5053-WH plate.
Fig. 6: Your new TV Multimedia Recessed Box is now installed and ready for the TV mount to be installed. Install your TV mount bracket per the TV
bracket manufacturer's instructions.
WARNING
 CE Tech's products shall be installed and used only as indicated in CE Tech's product instruction sheet
 Instruction sheets are available online at www.homedepot.com.
CAUTION
 For shock protection, this device must be properly grounded.
 Use copper wire only with this device.
IMPORTANT INSTRUCTIONS
Read and understand all instructions.

Follow all warnings and instructions marked on the product.

Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a

swimming pool.
SAVE THESE INSTRUCTIONS.

Instruction / Installation Sheet TV Multimedia Recessed Box
Parts Included:
FOR ASSISTANCE, CALL:
• Recessed Box
SI NECESITA AYUDA,
LLAME AL:
• Snap-in cover plate with conduit/pipe knockouts
1-800-394-7519
• Old Work Electrical Box with four (4) Mounting Screws
HOMEDEPOT.COM
• Flexible Pass-Through Accessory Plate
• Six (6) Port Keystone Accesory Plate
• Blank Accessory Plate
Fig. 3
Fig. 1
Fig. 4
Page 1 of 2
Tools Required:
• Drill with Phillips Bit or Phillips Head Screw Driver
• Pen or Pencil
• Sheetrock Saw or Utility Knife
• 6 Ft. Tape Measure
Fig. 5
No. 5053-WH
Fig. 6
05/16/2016