Advertisement
REAR PANEL
@ AUDIO
INPUT jacks
@ LASERDISC
Connect to the AUDIO
jacks of a LD player.
Mm VCR
Connect to the AUDIO
OUT jacks of a VCR.
@ CABLE
For input of monophonic
audio signals from cable receivers
etc. When both terminals are connected select 1 or 2 using
the sending device.
@ TAPE/AUX
Can
be
connected
to
the
PLAY
(OUTPUT)
jacks
of a
cassette
deck
or to
the
OUTPUT
jacks
of other
audio
components.
@ VCR SOURCE SELECTOR SENSITIVITY switch
Switch it for proper operation of the AUTO
SOURCE
SELECTOR
function
of the SA-V210.
M : Normal
position
L:
(When
no LASERDISC
signal is input.)
if "TAPE/AUX"
or "CABLE"
terminal is automatically
selected
even
though
VCR
is being played
, set to this
position "L" to select VCR.
H:
(When
no LASERDISC
signal is input.)
lf "TAPE/AUX" or "CABLE" is not selected even though
VCR
finishes
its playback,
set to this position
"H"
to
select "TAPE/AUX" or "CABLE."
@ VCR VOLUME
control
Controls the volume
of the VCR
input terminals sound.
This control
is normally
centered
but should
be adjusted
in
accordance
with the volume
of the LASERDISC.
@ VCR MODE
switch
This
switch
is used
to
select
the
VCR
audio
mBdes
(MONO/STEREO).
:
Connect a VCR with monophonic audio output either to "L" or
"R" AUDIO INPUT jack and set this switch to "MONO."
&) CABLE VOLUME
control
Controls the volume
of the CABLE
input terminals sound.
This control
is normally
centered
but should
be adjusted
in
accordance
with the volume
of the LASERDISC.
© TAPE/AUX
SOURCE
SELECTOR
SENSITIVITY
switch
Switch
it for
proper
operation
of
the
AUTO
SOURCE
SELECTOR
function of the SA-V210.
M:
Normal
position
L:
(When
neither LASERDISC
nor VCR
signal is input.)
Hf "CABLE"
is automatically
selected
even
though
"
TAPE/AUX"
signal is being played , set to this position "
L" to select "TAPE/AUX."
H:
(When
neither LASERDISC
nor VCR
signal is input.)
If AUTO INPUT selector remains at "TAPE/AUX" even
though
TAPE/AUX
finishes
its
playback,
set
to
this
position "H" to select "CABLE."
@® TAPE/AUX VOLUME control
Controls
the
input
sound
level
of devices
connected
to the
TAPE/AUX input jacks. This control is normally centered but should
be adjust for LASERDISC.
34
TAPE/AUX
MODE
switch
This switch
is used to select audio modes
(MONO/STEREO)
of
components connected to the TAPE/AUX
input jacks. Connect a
component
with monophonic
audio output either to ''L'' or "'R'"'
AUDIO
INPUT jack and set this switch to "MONO."
@ VISUAL
INPUT jacks
@ 1 LASERDISC
Connect to the VIDEO
OUT jack of the LD player.
@ 2 VCR/CAMERA
Connect to the VIDEO
OUTPUT jack of the VCR or TV camera.
VISUAL OUTPUT jacks
@1-3
Jacks
for connection
to the
VIDEO
INPUT
jacks
of TV
monitors
(maximum
three monitors).
M@ VCR/CAMERA
ONLY
Signals input to the "VCR/CAMERA" VISUAL INPUT jack
of the SA-V210
will always be output. By connecting to a
TV monitor, you can monitor a VCR or TV camera.
@ SPEAKERS terminals
Two
speaker
systems
(A
and
B) can
be
connected.
For
details.
©
Always
connect
the pius (+) and minus
(—) wires of the
speakers to the speaker terminals
of the same
polarity. A
polarity error can cause
unnatural sound.
@ VOLTAGE SELECTOR
@® MIC input jacks 1,2,3
Microphones
cannot
be connected
directly to the SA-V210.
When
placing
the
SA-V210
into
a rack
with
MIC
cords,
connect the MIC cords of the rack. When
using microphones
with key control
remote
switch
connected
to MIC
1 and 2,
connect the control
cords to the KEY CONTROLLER
jacks.
lf a microphone
is connected
to the MIC
jack on the front
panel, front input has priority.
NOTE:
¢
Position
of
the
key
controller
may
change
by
connecting/disconnecting
of the remote plug. In such a case,
set it again to the desired position.
¢
For the key control
function,
both
front and rear inputs
are
effective.
AUDIO OUTPUT MONITOR L + R jack
The
L and
R audio
signals
input to the
audio
input jacks
(LASERDISC,
VCR,
CABLE,
TAPE/AUX)
always
appear
as L
+ R monaural.
@ AUDIO
OUTPUT jacks
These jacks are used to output the L and R audio signals to the audio
input jacks (LASERDISC,
VCR, CABLE, TAPE/AUX)
of this unit.
© HOWLING CUT switch
In case of howling, set this switch to "ON."
@ TAPE REC jacks
Connect
to the REC
(INPUT)
jacks of a cassette
deck.
Mic
mixing recording will be possible, because
signals processed
with microphone
mixing are output.
When
"TAPE/AUX"
or "CABLE"
has been selected, no sound
can be heard.
Advertisement
