Table of Contents
Advertisement
Quick Links
The Gas Griddle
Installation and Operation Instructions
Model: GT1200/GT100/GT900/GT750/GT600/GT500/GT350/GT718/GT720
Gas catering equipment (Type A) EN 203-1:2014 / BSEN 203-2-9:2005
Please complete this information and retain this manual for the life of the equipment. For Warranty
Service and/or parts, this information is required.
These instructions are only valid if the country code appears on the appliance. If the code does not
appear on the appliance, refer to the technical instructions for adapting the appliance to the conditions
for use in that country".
WARNING: For your safety, do not store or use gasoline or other flammable vapors or
liquids in the vicinity of this or any other appliances. Keep the area free and clear of
combustiable.
WARNING ： Improper installation, adjustment, alteration, service or maintenance can
cause property damage, injury, or death. Read the installation operating and maintenance
instructions thoroughly before installing, or servicing this equipment.
WARNING：Instructions must be posted in a prominent location. All safety precautions
must be taken in the event the user smells gas. Safety information can be obtained from
your local gas supplier.
IMPORTANT FOR FUTURE REFERENCE
V0.Rev0.00-17
Advertisement
Table of Contents
Summary of Contents for infernus GT1200
- Page 1 The Gas Griddle Installation and Operation Instructions Model: GT1200/GT100/GT900/GT750/GT600/GT500/GT350/GT718/GT720 Gas catering equipment (Type A) EN 203-1:2014 / BSEN 203-2-9:2005 IMPORTANT FOR FUTURE REFERENCE Please complete this information and retain this manual for the life of the equipment. For Warranty Service and/or parts, this information is required.
-
Page 2: Table Of Contents
Contents Introduction ........................... 1 Safety Notices and Precautions .................. 2 Specifications ........................4 General Pack Contents Product specification list Pressure point Gas connection Feet adjusting height Gas categories and pressure values Dimensions ..........................6 Installation ..........................7 Installation Requirements Unpacking Location Clearances Assembly... -
Page 3: Introduction
Introduction Dear customers and users： We are confident that you will be delighted with your Gas Griddle, and it will become a most valued appliance for you. To ensure you receive the utmost benefit from your new Gas griddle, there are two important things you can do. -
Page 4: Safety Notices And Precautions
Safety Notices and Precautions When using this equipment, safety precautions should always be followed, including the following: Please make sure that the operator is an authorized and licensed technician before you allow him/her to install and operate the products. Be sure to strictly follow this instruction guide during installation and using. - Page 5 Safety Notices and Precautions Always keep hands, hair and clothing away from heating source. Wait the unit cools down before cleaning. Because the unit is too hot to handle after using. The parts protected by the manufacturer or his agent shall not be adjusted by the installer. ...
-
Page 6: Specifications
Pack Contents The following is included: The Gas griddle Plate • Four Feet • • Instruction Manual • Flue baffle Product specification list: GT1200 GT1000 GT900 GT750 GT600 GT500 GT350 GT718 GT720 Burners Heat Total 15KW... -
Page 7: Gas Categories And Pressure Values
SPECIFICATION Table 1: Gas categories and pressure values Manufacturer Guangzhou Gainco Catering Equipment Co.,Ltd Product Name Gas Griddle PIN:0063CS7931 3+(28-30/37) 3B/P(30) 3B/P(37) 3B/P(50) Country code BE, CH, CY, BE, CY, DK, AT,CH, AT, BG, CZ, CZ, ES, FR, EE, FI, FR, DE,SK DK, EE, FI, GR, GB, GR, IE,... -
Page 8: Dimensions
Dimensions GT1200 serils GT718 / GT720 serils... -
Page 9: Installation
Installation Installation Requirements NOTE: • It is most important that this appliance is installed correctly and that operation is correct before use. Installation shall comply with local gas, health and safety requirements. • This appliance shall be installed with sufficient ventilation to prevent the occurrence of unacceptable concentrations of substances harmful to health. -
Page 10: Clearances
Installation Clearances NOTE: Only non-combustible materials can be used in close proximity to this appliance. Combustible Surface Non Combustible Surface Left / Right Hand Side Not applicable 100mm Min. Rear Not applicable 100mm Min. Bottom Not applicable 100mm Min. Assembly NOTE: ... - Page 11 Installation LP Gas hose connection Nature gas connection , Gas hose adaptor, seal gasket, gas pipe, LP or nature regulator NOTE: Manual Isolation Valve and flexible hose were not included with current product. Purchase them in your local site. The gas type and gas pressure shall be matched with gas rating label in product body.
-
Page 12: Lp Gas Cylinder And Compartment
test. Steps are as following: Installation Turn over gas griddle , and needle type pressure joint screw arbor (Fig.1), then slip rubber tube of pressure gauge over needle type pressure joint; Start the equipment in accordance with the instructions, measuring gas supply pressure (dynamic pressure) in the work state;... - Page 13 fresh air is ensured and there is no accumulation of un-burnt gases.
-
Page 14: Commissioning
Installation Commissioning Before leaving the new installation; a. Check the following functions in accordance with the operating instructions specified in the ‘Operation’ section of this manual. Turning 'Off' the Main Burner. Electrical battery installation Light the Main Burner. ... -
Page 15: Operation
Operation Operation Guide CAUTION: • This appliance is for professional use and is only to be used by qualified persons. • Only authorized service persons are to carry out installation, servicing or gas conversion operation operations. • Components having adjustments protected by the manufacturer should not be adjusted by the user/operator. -
Page 16: Lighting Main Burners
Operation Lighting Main Burners The Griddle are fitted with Flame Failure Protection is incorporated for each burner by way of a thermo-electric system which will shut off the gas supply to that burner in the event that the burner goes out, so that un-burnt gas is not expelled. Before using electronic pulse ignition, open the bottom and put a No.7 battery in it Turn the knob to align”... - Page 17 A properly designed and installed hood will act as the heart of the ventilating system for the room or area in which the unit is installed, and will leave the unit independent of changing draft conditions. All valves must be checked and lubricated periodically. This must be done by an authorized service representative in your area.
-
Page 18: Cleaning And Maintenance
Cleaning and Maintenance CAUTION: Always turn off the gas supply before cleaning. This appliance is not water proof. Do not use water jet spray to clean this appliance. GENERAL Clean the Gas Griddle regularly. A clean Gas Griddle looks better, will last longer and will perform better. - Page 19 Cleaning and Maintenance Burners a. Remove the burner from the top of the bracket of appliance b. The burners should be cleaned with a mild detergent and hot water solution using a soft bristled brush. Dry thoroughly with a dry cloth. Stainless Steel Surfaces a.
-
Page 20: Trouble Shooting
Trouble Shooting This section provides an easy reference guide to the more common problems that may occur during the operation of your equipment. The fault finding guide in this section is intended to help you correct, or at least accurately diagnose problems with your equipment. Although this section covers the most common problems reported, you may encounter a problem not covered in this section. - Page 21 Replacement Parts list IMPORTANT: Only genuine authorized replacement parts should be used for the servicing and repair of this appliance. The instructions supplied with the parts should be followed when replacing components. For further information and servicing instructions, contact your nearest authorized service branch. When ordering replacement parts, please quote the part number and the description listing below.
-
Page 22: Parts List
Explosion Drawing GT1200 exploded drawing Parts List NO.DESCRIPTION DESCRIPTION Solid plate Assembly Bottom support panel Flue assembly St4.2x9 Self screws Manifold pipe assembly M5 flange nut Control panel Control knob Main burner YD1.5-2B Igniter Foot YD1.5-3B Igniter Side panels M5x12 flat screw... - Page 23 GT1000 exploded drawing Parts List NO.DESCRIPTION DESCRIPTION Solid plate Assembly St4.2x9 Self screws Flue assembly M5 flange nut Manifold pipe assembly Control knob Control panel YD1.5-2B Igniter Main burner YD1.5-2B Igniter Foot Bottom support panel Side panels M5x12 flat screw Back panel Slip hoop Clapboard...
- Page 24 GT900 exploded drawing Parts List NO.DESCRIPTION DESCRIPTION Solid plate Assembly St4.2x9 Self screws Flue assembly M5 flange nut Manifold pipe assembly Control knob Control panel Main burner YD1.5-3B Igniter Foot Bottom support panel Side panels M5x12 flat screw Back panel Slip hoop Clapboard Side insulation panel...
- Page 25 GT750 exploded drawing Parts List NO.DESCRIPTION DESCRIPTION Solid plate Assembly St4.2x9 Self screws Flue assembly M5 flange nut Manifold pipe assembly Control knob Control panel Main burner YD1.5-3B Igniter Foot Bottom support panel Side panels M5x12 flat screw Back panel Slip hoop Clapboard Side insulation panel...
- Page 26 GT720 exploded drawing Parts List NO.DESCRIPTION DESCRIPTION Solid plate Assembly St4.2x9 Self screws Flue assembly M5 flange nut Manifold pipe assembly Control knob Control panel YD1.5-3B Igniter Main burner Bottom support panel Foot M5x12 flat screw Side panels Slip hoop Back panel Igniter cover Clapboard...
- Page 27 GT718 exploded drawing Parts List NO.DESCRIPTION DESCRIPTION Solid plate Assembly St4.2x9 Self screws Flue assembly M5 flange nut Manifold pipe assembly Control knob Control panel YD1.5-2B Igniter Main burner Bottom support panel Foot M5x12 flat screw Side panels Slip hoop Back panel Igniter cover Clapboard...
- Page 28 GT600 exploded drawing Parts List NO.DESCRIPTION DESCRIPTION Solid plate Assembly St4.2x9 Self screws Flue assembly M5 flange nut Manifold pipe assembly Control knob Control panel Main burner YD1.5-2B Igniter Foot Bottom support panel Side panels M5x12 flat screw Back panel Slip hoop Clapboard Side insulation panel...
- Page 29 GT500 exploded drawing Parts List NO.DESCRIPTION DESCRIPTION Solid plate Assembly St4.2x9 Self screws Flue assembly M5 flange nut Manifold pipe assembly Control knob Control panel Main burner YD1.5-2B Igniter Foot Bottom support panel Side panels M5x12 flat screw Back panel Slip hoop Clapboard Side insulation panel...
- Page 30 GT350 exploded drawing Parts List NO.DESCRIPTION DESCRIPTION Solid plate Assembly St4.2x9 Self screws Flue assembly M5 flange nut Manifold pipe assembly Control knob Control panel Main burner YD1.5-1B Igniter Foot Bottom support panel Side panels M5x12 flat screw Back panel Slip hoop Clapboard Side insulation panel...