Page 2
INSTALLATION INSTRUCTIONS SAFETY INSTRUCTIONS Throughout this manual, you'll see Warning and Caution notes. These warnings, cautions, and the important safety instructions that follow do not cover all possible conditions and situations that may occur. It's your responsibility to use common sense, caution, and care when installing, maintaining, and operating the dishwasher.
Page 3
Prior to removal of original dishwasher and the installation of your new unit, make sure to switch off your circuit breaker. Do not connect the dishwasher until you have completed the installation. Connecting the power cable is the last step when installing the dishwasher.
Page 4
Before Installing The Dishwasher Tip-Over Hazard Do not use the dishwasher until it is correctly installed. Do not push down on the door when it is open. Do not place excessive weight on the open door. Electric Shock Hazard Failure to follow these instructions can result in death, fire, or electric shock: Electrically ground the dishwasher Connect the ground wire to the green ground connector in the junction...
CONTENTS PREPARING THE DISHWASHER CABINET Product dimensions Cabinet dimensions INSTALLING THE DISHWASHER STEP 1 Check the parts and tools STEP 2 Select the best location for the dishwasher STEP 3 Check water supply requirements and cautions STEP 4 Check the electrical requirements and cautions STEP 5 Unpacking and inspecting the dishwasher STEP 6...
PREPARING THE DISHWASHER ENCLOSURE Product Dimensions The water supply 23" ⁄ line, power cable and drain hose should go through this space behind the dishwasher. min 26'' ⁄ ⁄ max 28'' Then, the power cable run in channels under the dishwasher to connections in the Front.
INSTALLING THE DISHWASHER Be sure that you or your installer follow these instructions closely so that the new dishwasher works properly and that you're not at risk of injury when washing dishes. Step 1 Check The Parts And Tools Before starting on the installation, prepare all the necessary tools and parts required to install the dishwasher.
Page 8
Electrical tape & Twist on wire Strain relief Standard duct tape connector Hot water supply line Tube fittings 90° Elbow Air gap Rubber connector Hose clamp Teflon tape or sealing Decoration door Power cable compound For the hot water supply line , We strongly recommend using copper tubing with a compression fitting or a flexible stainless steel braided hot water supply line.
INSTALLING THE DISHWASHER New installation If the dishwasher is a new installation, most of the installation work must be done before the dishwasher is moved into place. Replacement If the dishwasher is replacing an old dishwasher, you must check the exising dishwasher connections for compatibility with the new dishwasher.
tep 3 Check Water Supply Requirements And Cautions The hot water supply line pressure must be between 5.80~145.04 PSI Adjust the water heater to deliver water between 120 ° F(49° C) ~149 ° F(65° C). The dishwasher must be connected to a hot water supply between 120 °F(49°C)~149 °F(65°C). This temperature range provides the best washing result and shortest cycle time.
INSTALLING THE DISHWASHER Step 4 Check The Electrical Requirements And Cautions The electrical requirements for the dishwasher are as follows: In the United States, install in accordance with the National Electric Code/State and Municipal codes and/or local codes. In Canada, install in accordance with the Canadian Electric Code C22.1-latest edition/Provincial and Municipal codes and/or local codes.
Step 5 Unpacking And Inspecting The Dishwasher unbox the dishwasher in an open area free of obstruction both around the carton and overhead. We recommend that you retain the carton and all of the packing materials until the dishwasher is fully installed and operational to ensure you have removed all the product's components from the carton prior to disposal.
Page 14
INSTALLING THE DISHWASHER Plumbing 1. Check the hot water connection on the front left-side of the base of the dishwasher. The mountingplate should be secured to the front of the base, the threads inside the connection should be smooth and shiny, and the area should be clean and free of any debris.
Step 6 Preparing The Dishwasher 1. Ensure that the circuit breaker and water supply valve are turned off before proceeding with the following steps. Before you move or lay down the dishwasher for installation, make sure to adjust the height of the legs so the legs are as short as possible.
INSTALLING THE DISHWASHER Step 7 Placing The Dishwasher And Connecting The Hot Water Supply Line 1. Adjust the three leveling legs at the bottom of the dishwasher after measuring the height of the cabinet opening from under the countertop to the floor. (See Step 8, Leveling the Dishwasher.) 2.
Step 8 Leveling The Dishwasher 1. Open the door and place the level against the top of the tub on the inside and check if the the dishwasher is level.If it is not level, rotate the leveling legs at the bottom front of the dishwasher until the dishwasher is level.See the first note below for instructions on adusting the height of the front legs.
INSTALLING THE DISHWASHER Step 9 Securing The Dishwasher You must fix the dishwasher to the countertop or cabinet side walls for additional stability and safety. If the countertop is made of wood or the material will not be damaged by drilling, follow the instructions in 2-1 below.
Adjustment cap Screw to side wall Step 10 Connecting The Drain Hose 1. Check the parts on the sink to which the drain hose will be connected. 2. There are several ways to insert the drain hose into the drain hose connector of the sink, as shown in the following figures.
Page 20
INSTALLING THE DISHWASHER Case 2. With disposal With disposal Disposal with an air gap Drain hose2 Check the size of the sink's drain hose connector( - as shown in Figure 11 below). 13/16" - 21 mm If the end of the drain hose does not fit onto the drain hose connector of the sink, use an adaptor purchasable at a plumbing/hardware supply store.
Page 21
The drain hose internal 13/16" (21 mm) diameter is Secure the drain hose to the sink wall using cable ties or other fastening materials. Otherwise, the drain hose may bend at the end. causing a drainage problem or excessive supply of water. Front of dishwasher Counter TOP NOTE:...
INSTALLING THE DISHWASHER Step 11 Wiring Connections Before connecting the power cable to the dishwasher, make sure the circuit breaker is off. In the junction box located at the front bottom right of the dishwasher, find the three power wires from the dishwasher including the grounding line.
Step 12 Completing The Installation 1. Open the door and remove all foam, paper packaging, and unnecessary parts. 2. Turn on the circuit breaker you turned off before you began the installation. 3. Open the water supply valve to supply water to the dishwasher. 4.
Page 25
Step 12 Completing The Installation 7. Tension adjustment of the door spring. The door springs are set at the factory to the proper tension for the outer door. If the decoration door is installed, you will have to adjust the door spring tension. Rotate the adjusting screw to drive the adjustor to strain or relax the steel cable, see figure 20.
SPECIFICATIONS Power supply 120 V 60 Hz Water pressure 5.80~145.04 PSI Dimensions 23" 9/16inx21" 5/8inx32"1/16in (Width x Depth xHeight) Nominal inlet water 120 ° F(49° C)~149 ° F( ° C) temperature Specifications are subject to change without notice for quality improvement purposes. The actual appearance of the dishwasher may differ from the illustrations in this manual.