Source SBOL 450 Installation Manual

Read these instructions before commencing installation. Please retain for future reference.
Installation Sheet

Installation Guide for SBOL 450 / SBOL 750

IP65
Read these instructions before commencing installation. Please retain for future reference.
These fittings are Class II and do not require an Earth
IP65

Important Information

• It is recommended that these luminaires are installed and fitted by a qualified electrician
These fittings are Class II and do not require an Earth
with current IEE wiring regulations & local building control.
These products are designed for connection to a 240V~50Hz supply.
•
Important Information
Any faulty, broken or damaged luminaires should be replaced immediately.
•
• It is recommended that these luminaires are installed and fitted by a qualified electrician
with current IEE wiring regulations & local building control.
Please Note: The limited warranty shall be deemed null and void in the following circumstances: Failure by the installer, e
• These products are designed for connection to a 240V~50Hz supply.
any third party to exercise caution to protect any covered product or part from outside damage, adverse temperature (no
• Any faulty, broken or damaged luminaires should be replaced immediately.
operating ambient temperature -15 ~ +40°C), humidity conditions, fluctuations in the electrical system or physical abuse
Please Note: The limited warranty shall be deemed null and void in the following circumstances: Failure by the installer, end user or
failure related to workmanship in the installation of the products or parts.
any third party to exercise caution to protect any covered product or part from outside damage, adverse temperature (normal
operating ambient temperature -15 ~ +40°C), humidity conditions, fluctuations in the electrical system or physical abuse as well as

Important User Advice

failure related to workmanship in the installation of the products or parts.
Always switch off mains supply before servicing lamp changes and maintenance.
Important User Advice Please ensure that a suitable maintenance schedule is performed including greasing any exposed metal parts and clean
non-abrasive cleaner to ensure the product gives you a long lasting trouble free life.
Always switch off mains supply before servicing lamp changes and maintenance.
Please ensure that a suitable maintenance schedule is performed including greasing any exposed metal parts and cleaning with a

Installation Procedure

non-abrasive cleaner to ensure the product gives you a long lasting trouble free life.
Safely isolate the mains supply before installation.
Installation Procedure
Remove the head by loosening the grub screw and twisting anticlockwise.
Safely isolate the mains supply before installation.
Route the cable through the cable gland (8mm-12mm) and terminate wiring as per Figure 1.
Remove the head by loosening the grub screw and twisting anticlockwise.
Install suitable lamp not exceeding the maximum wattage.
Route the cable through the cable gland (8mm-12mm) and terminate wiring as per Figure 1.
Refit the head in reverse of removal ensuring the seal is clean, in place and undamaged, grease the grub screw and tigh
Install suitable lamp not exceeding the maximum wattage.
Tighten the cable gland ensuring a water tight connection.
Refit the head in reverse of removal ensuring the seal is clean, in place and undamaged, grease the grub screw and tighten.
Secure the bollard in place using suitable fixings for the application.
Tighten the cable gland ensuring a water tight connection.
Turn mains supply on and test luminaire.
Secure the bollard in place using suitable fixings for the application.
Never touch a hot lamp.
Turn mains supply on and test luminaire.
Never touch a hot lamp.
Fig.1
Fig.1
Mains Supply
Mains Supply
Neutral
ring the installation complies
Lamp Cap: E27 GLS
Lamp Cap: E27 GLS
ilure by the installer, end user or
Wattage: 60W (max)
Wattage: 60W (max)
erse temperature (normal
Only branded lamps are recommended
Only branded lamps are recommended
metal parts and cleaning with a
e grub screw and tighten.
240V~50Hz 60W max.
0.3m
240V~50Hz 60W max.
0.3m
Luminaire
Luminaire
Neutral N - Blue
N - Blue
Live L- Brown
Live L- Brown

Lamp Details

Lamp Details
Available finish - Black
ensuring the installation complies
Manta
Available finish:- Black
135mm
200mm
Base Diameter
E27 Bollards
ensuring the installation co
E27 Bollards
135mm
200mm
Base Diameter