Table of Contents
Advertisement
I
TRANSAXLE
The transaxle is lubricated and sealed at the lactory
and does not require checking. If disassembled lor any
reason, lubricate with 10 oz. of grease, part n jmber
737-0148.
WHEELS
The front wheels are provided with grease fittings. The
rear wheels must be removed from the axle for lubrica¬
tion. Lubricate both front and rear wheels at least once
a season with automotive multi-purpose greas
3
.
PIVOT POINTS
Lubricate all pivot points with light oil at least c^nce a
season.
MAINTENANCE
WARNING: Disconnect the spark pfuij wire
and ground against the engine befors per¬
forming any repairs or maintenance;.
TROUBLE SHOOTING
Refer to page 20 of this manual for trouble shooting
information.
CRANKCASE OIL
Check the oii level in the crankcase before each use
of the machine and after every five hours of opeiation.
Oil level should be maintained as instructed n the
separate engine manual.
After the first five hours of operating a new engine drain
the oil from the crankcase while engine is still hot and
refill crankcase with new oil; thereafter change he oil
every 25 hours of operation. Refer to the engine
manual.
AIR CLEANER
Under normal operating conditions, the air cluaner,
located on top of the carburetor, must be service( I after
every ten hours of use. Under extremely dusty
operating conditions, the air cleaner must be sei viced
after every hour of operation. To service the air cluaner,
refer to the separate engine manual packed with your
unit.
CLEANING ENGINE AND BLADE HOUSING
Any fuel or oil spilled on the machine should be viped
off promptly. Grass, leaves, and other dirt must not be
left to accumulate around the cooling fins of the e ngine
or on any part of the machine.
Clean the underside of the blade housing after each
mowing.
SPARK PLUG
The spark plug should be cleaned and the gap reset
once a season. Spark plug replacement is recommend¬
ed at the start of each mowing season; check engine
manual for correct plug type and gap specification.
CUTTING BLADE
A. Removal for Sharpening or Replacement
WARNING: Be sure to disconnect and
ground the spark plug wire and remove ig¬
nition key before working on the cutting
biade to prevent accidentai engine start¬
ing. Protect hands by using heavy gloves
or a rag to grasp the cutting biades.
1. Remove the large bolt and lock washer which holds
the blade and adapter to the blade spindle.
2. Remove the blade and adapter from the spindle.
3. If the blade or blade adapter needs replacing,
remove the two small bolts, lock washers and nuts
which hold the blade to the adapter.
B. Sharpening
Remove the cutting blade by following the directions
of the preceding section.
When sharpening the blade, follow the original angle
of grind as a guide. It is extremely important that each
cutting edge receives an equal amount of grinding to
prevent an unbalanced blade. An unbalanced blade will
cause excessive vibration when rotating at high speeds,
may cause damage to the mower and could break,
causing personal injury.
The blade can be tested for balance by balancing it on
a round shaft screwdriver. Remove metal from the
heavy side until it balances evenly.
NOTE: It is recommended that the blade always be
removed from the adapter for the best test of balance.
C. Reassembly
Before reassembling the blade and the blade adapter
to the unit, lubricate the spindle and the inner surface
of the blade adapter with light oil. Lubricating the bolt
holes, bolts and inner surface of the nuts with light oil
is also recommended. A 4 oz. plastic bottle of light oil
lubricant is available. Order part number 737-0170.
Engine oil may also be used.
When replacing the blade, be certain the wide blade
is assembled on the right side of the deck. Be sure to
install the blades with the side of the blades marked
"Bottom" (or with part number) facing the ground when
the mower is in the operating position.
Blade Mounting Torque
3/8" Dia. Bolt 375 in. lb. min., 450 in. lb. max.
5/16" Dia. Bolt 150 in. lb. min., 250 in. lb. max.
To insure safe operation of your unit, ALL nuts and bolts
must be checked periodically for correct tightness.
FUEL FILTER
Your unit is equipped with a replaceable in-line fuel
filter. Replace filter whenever contamination or
discoloration is noticed. Order replacement filter
through your engine authorized service dealer.
16
Advertisement
Table of Contents
