Advertisement
Quick Links
Models 12560-000!
r2570.OOOt
Puppy Sefies
SELF.PRIMING PUMPS
FEATURES
Body:
Plastic
lmpeller:
JabscoNeoprenecompound
Seal:
Lip type
Slipon babsforS/8" LD. hoso
Perman€nt magnet type, f ully enclosed,
stainless steel shaft. Fus€ and
fuseholder included,
Dimensions: 3" (76 mm) high, 6-3/8" (162 mm) long,
4" (102 mm) wide
Weight:
4% lbs (2 kg) approx.
[Iotor meeis USCG Electrical Slandards (Title33, Chapter
I, Parl 183; Subpart l) for IGNITION PFOTECTION on
gasoline powered vessels.
WARNINGT DO NOT PUMP SOLVENTS,
THINNERS
OF GASOLINE AS EXPLOSION MAY BESULT
CAUSING PERSONAL INJURY OR DEATH.
OPERATION
Flexibl€ impeller pumps must NOf be run dry as the
pumped liquid islhe lubricantfo.the impellor Obs€rve iho
outlot and shul oft pump assoon as liquid stops llowing. An
automalic levelswitch is convenienl to controllhe oumo.
NOrICE- lt pump is idleforexlended periods, the impeller
may sticklolhe pump body, pr€v€nling motor rotation and
causing blown fuses. To correct, remove end covet and
impeller Clean body and impeller, then lubdcate with wat€r
or small amounts of grease before assembly.
Temperatureof
pumped liquid may be in the range of 45o -
1600F (100 -700c).
Pressure lor normaloperation
should nol exceed 20 feet of
head (6,1m).
CAUTION: l'rotor runs hot; about 180"F (82qC) is a nonnal
lempeatuG. Prolonged contact during ope6tion fiay
cause a Duft.
Motor:
=
CAUTION: Do not operate with acrews rcmoved licm
motor caae. Explosion resultlng In peJEonal inlury
death or ptoperty damage may occur. Case openings
must be gealod lo a\oid exploslon and malnlain lgnltlon
protecled ratlng.
APPLICATION
Usefor bilge pumping, live well circulation, washdown and
generalpumping requirements.
lf bilge water contains
significant amount ofoil, thestandard impellershould be
reolaced with imoeller #6303-0003 which is an oiFresbtanl
nitrile matorial. With awet impellei pump willproduce a
suction lifl ol aboul4 feet (1,2m) and a litt of 20 feet (6m)
when primed. lllhe pump is dry itwillprime aboul l.5 feet
10.47m).
BE SURE SUCIION LINES ARE AIR TIGHI
INSTALLATION
The pump must be mounted in adry location - the molor
is not waterproof and must notbe submerged. SELECTION
.
OF A COOL, VENTILATED location willgenerally extend
-
pump motor lile. The unit can be mountea in any ijesired
position. lt is best to mount so that water dripping lrom
loose portconnection willnolwetthe motor. The pump
head may be mounted al lS0degree increnents on the
motor to allowchange in llowdirection.
VARIATIONS AVAILABLE
MODELS
VOLTAGE
DRAW
12560-0001
1257G0001
'12 Volt dc
24 Volt dc
7
10
TOTAL HEAD
CAPACITY
p,s,t,
leet
mettes
GPM
l/min
4.3
4.7
Open Flow
5
1 0
20
1 , 5
3,0
5.0
4.6
1 . 7
18,9
17,4
14,O
6,4
Table shows approximate Head-Flow ror newpump.
Advertisement
