Advertisement
Quick Links
Four Bike Platform Mount Carrier
7"
6"
14-1/4"
Assembly Instructions
STEP 1
Assemble the primary frame by connecting the Short
Support Base Assembly (part #1) and (2) Horizontal
Arms (part #2), using (2) 5/16" knob, (4) 5/16" flat
washer, (2) 5/16" spring washer, (2) 5/16" hexagon
bolt, (2) M10 Carriage bolts and (2) M10 Locknuts
(parts #3, #4, #5, #6, #27 and #28). (See Figure 1)
FIGURE 1
BC-204
Fits 2"x2" receiver
32"
19-1/4"
10"
10"
1-3/8" square tubing
51-1/2" long
Place Vertical Arm (part #7) into the Short Support Base Assembly
by using M10 Carriage Bolt and M10 Locknut (parts #27 and #28).
With the Vertical Tube in a vertical position, insert the 5/16" hexagon
bolt (part #6), through the 5/16" flat washer (part #4), the 5/16"
spring washer (part #5) and the 5/16" flat washer (part #4), tighten
with 5/16" knob (part #3). (See Figure 2)
StrombergCarlson.com • 231.947.8600
Four Bike
Platform Mount Carrier
Model: BC-204
Fits 2" receiver
n
n Tilts down for access to vehicle
n Wheel mounts adjust to any size frame
n Tire cradle fits up to 2-1/2" wide tire
(BC-2FT Fat Tire Adaptor available)
n Weight capacity 160 lb
Tools Needed
(1) 17mm Open Wrench
(1) 19mm Open Wrench
(1) 24mm Open Wrench
NOT TESTED ON OR APPROVED
FOR E-BIKES
STEP 2
FIGURE 2
INS-BC204-C 10.27.2022
BC-204
NOTICE
The sliding
teeth face
this direction
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Stromberg Carlson Products BC-204
Summary of Contents for Stromberg Carlson Products BC-204
- Page 1 Four Bike Platform Mount Carrier BC-204 Fits 2"x2" receiver Four Bike Platform Mount Carrier Model: BC-204 Fits 2” receiver 32" n Tilts down for access to vehicle n Wheel mounts adjust to any size frame n Tire cradle fits up to 2-1/2” wide tire...
- Page 2 Four Bike Platform Mount Carrier BC-204 STEP 3 Attach Folding Shank (part #8) to Short Support Base Assembly tube, using M16 Bolt and M16 Locknut (parts #9 and #12) and using 5/8” Pin and Clip (parts #10 and #11) for extra safety.
- Page 3 Four Bike Platform Mount Carrier BC-204 STEP 7 Slide the Left and Right Cradle Assemblies (parts #17 and #18) onto the Horizontal Arms. Release the knob of the left and right cradle. The knob should be facing up and the loop end of cradle should be facing outward and upward.
- Page 4 Four Bike Platform Mount Carrier BC-204 STEP 11 STEP 12 Load bicycle into Wheel Cradles. Adjust cradles to Rotate vertical tube to vertical position and lock with the appropriate position. Ensure 5/16 “knob. Lower J-Hook tire is well supported at...
-
Page 5: Hardware Kit
Four Bike Platform Mount Carrier BC-204 FOLDED WHEN NOT IN USE FEATURE Fold Vertical Arm to the horizontal position, and then fold the Folding Shank Assembly to the vertical position. (See Figure 17) FIGURE 17 HARDWARE KIT PART # DESCRIPTION... -
Page 6: Assembly Diagram
Four Bike Platform Mount Carrier BC-204 ASSEMBLY DIAGRAM PART # DESCRIPTION PART # DESCRIPTION PART # DESCRIPTION Short Support Base Assembly 1 Long Support Base Assembly 1 16 Flat Washer Horizontal Arm Short Stabilizing Pin Wheel Cradle Strap 5/16” Knob 1/2”...
Need help?
Do you have a question about the BC-204 and is the answer not in the manual?
Questions and answers