Page 2
Manual for Energy Storage SystemTW6000(6000P) Legal Notices The copyright of this product belongs to Shenzhen Lithtech Energy Co., Ltd. Without the written permission of the copyright party, no unit or individual may extract, reproduce or translate in any way. Infringement must be investigated.
Page 3
Manual for Energy Storage SystemTW6000(6000P) Precautions Warning 1.It is strictly forbidden to place the battery in water or fire, so as to avoid explosion or other dangers, endangering personal safety. 2. Please connect the cables properly during installation, do not reverse the positive and negative poles;...
Page 4
Manual for Energy Storage SystemTW6000(6000P) Foreword Manual Description TW6000(6000P) lithium iron phosphate battery storage system can provide power storage function for photovoltaic power generation users through parallel combination. During the day, the excess power of solar energy can be stored in the battery, and at night or when needed, the stored energy is used to power electrical equipment, which can improve the efficiency of solar energy, peak shaving, and emergency power backup.
Manual for Energy Storage SystemTW6000(6000P) 1.Introduction 1.1 Introduction The TW6000(6000P) lithium iron phosphate battery system is a standard battery system unit. Customers can choose a certain quantity of TW6000(6000P) according to their needs, and form a larger capacity battery pack in parallel to meet users' long-term power supply needs. The product is especially suitable for applications with high operating temperature, limited installation space and long service life.
Manual for Energy Storage SystemTW6000(6000P) Product Identification Definition Voltage of battery is higher than safety voltage, it’s dangerous to touch Operate carefully. Read manual before operation Default battery can’t be thrown to trash can. Please recycle the battery after serving CE standards are met.
Manual for Energy Storage SystemTW6000(6000P) Item Name Definition Ground point Positive socket Battery output positive or parallel positive cable Negative socket Battery output negative or parallel negative cable DIP switch When the "OFF / ON" key is ON, press and hold SW (Wake on battery / this key for 3 seconds.Put the battery into the Sleep switch)
Manual for Energy Storage SystemTW6000(6000P) 2.3.2 Indicator definition and description Table 2-4 LED working status indication Battery indicator Normal/ Description Status Alarm / Protection ● ● ● ● ● ● Shutdown Dormant off off All off Normal standby mode According to battery Standby indicator Alert...
Manual for Energy Storage SystemTW6000(6000P) ●Running lights Table 2-6 Flash description Remarks Flashing way Flashing 1 0.25S 3.75S Flashing 2 0.5S 0.5S Flashing 3 0.5S 1.5S Remarks:Flash 1 is short for F1;Flash 2 is short for F2;Flash 3 is short for F3. Notes: The alarm can be enabled or disabled through the host computer.
Manual for Energy Storage SystemTW6000(6000P) Connect the charger. The output voltage of the charger must be greater than 48(51.2)V. Press the button (3 ~ 6S), and release the button. Note: After single or overall over-discharge protection, it enters low power consumption mode, and wakes up at regular intervals every 4 hours to turn on charge and discharge MOS.
Manual for Energy Storage SystemTW6000(6000P) 2.4.4 Other Protection Short circuit protection: When the battery is activated from the off state, if there is a short circuit, the system will start the short circuit protection for 30 seconds Shut down automatically: When the equipment has no external load and power supply for 10 hours, it will automatically shut down.
Manual for Energy Storage SystemTW6000(6000P) The ideal ambient temperature is 15 ~ 30 ℃ Keep away from dust and dirty areas 3.1.2 Tools The tools and meters that may be used in Table 3-1: Table 3-1 Tools Name screwdriver Slotted screwdriver multimeter Phillips screwdriver...
Page 16
Manual for Energy Storage SystemTW6000(6000P) and recorded. The packing list is as follows: Part name Specification Quantity Picture 48(51.2)V210Ah Battery module 780×556×199mm Positive parallel line /25mm²/L700mm (Optional) Negative parallel line Black /25mm²/L700mm (Optional) Positive power line /25mm²/L2050mm (Optional) Negative power line Black /25mm²/L2050mm (Optional)...
Manual for Energy Storage SystemTW6000(6000P) 3.1.5 Engineering coordination Note the following before construction: Power cord specifications Power cord specifications should meet the maximum discharge current requirements of each product Installation space and load Ensure that the battery has sufficient installation space, and that the case and bracket where the battery is installed have sufficient load-bearing capacity.
Manual for Energy Storage SystemTW6000(6000P) 3.2.2 Mechanical installation Method 1: Pendant bracket installation 1. Put the hanger bracket close to the wall, and mark the wall according to the space,Then use a percussion drill according to the vacancy of the pendant, drill 8 holes with a depth of 100mm 2.
Manual for Energy Storage SystemTW6000(6000P) 2.Use 4 M5-20mm screws to lock the bracket and battery pack; 3.2.3 Electrical installation Before connecting the power supply and ground wire, it is recommended to use a multimeter to measure the on-off and short circuit of the cable, confirm the positive and negative poles, and label the cable.
Page 20
Manual for Energy Storage SystemTW6000(6000P) Inverter Air switch Negative Positive Negative parallel wire power line power line Positive parallel wire Communication line between host and inverter Slave Parallel communication line PNG1 PNG2 PNG3...
Manual for Energy Storage SystemTW6000(6000P) Remark: 1、When the four sets are used in parallel, the dialing mode is as follows: the host dials the code according to the PNG1, the slave1 dials the code according to the PNG2, 2、When it is used independently, the dial switch does not need to be turned, as shown in PNG3.
Manual for Energy Storage SystemTW6000(6000P) ≤20.0 kW 80.0 4 * Combination box T-20.0 80.0 ≤25.0 kW 100.0 5 * Combination box T-20.0 100.0 Continuous charging current≤0.5C Charge If the battery capacity indication is empty, please charge within 48 hours after the power is discharged. Using requirements Continuous charging current≤0.5C...
Page 23
In case of special technical difficulties or questions, please contact the seller in time. SHENZHEN LITHTECH ENERGY CO.,LTD Room 711, Building A, Zhihui Innovation Center, Xixiang Street, Bao’an District, Shenzhen Postal code: 518101 E-mail: info@lith-tec.com...