Related Manuals for UNV OEA-EL12
Summary of Contents for UNV OEA-EL12
- Page 1 Electric Bolt Lock Installation Guide V1.0.0 Internal Use Only Electric Bolt Lock Installation Guide V1.0.0 Zhejiang Uniview Technologies Co., Ltd.
- Page 2 Electric Bolt Lock Installation Guide V1.0.0 Internal Use Only Revision History Date Manual Version Description Author 1/15/2023 V1.0.0 Initial release GW3317 Zhejiang Uniview Technologies Co., Ltd. www.uniview.com 2/ 12...
-
Page 3: Table Of Contents
Electric Bolt Lock Installation Guide V1.0.0 Internal Use Only Contents 1 Overview · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 4 2 Installation ·... -
Page 4: Overview
Internal Use Only Overview OEA-EL12 electric bolt lock can lock/unlock doors by current on/off. It has adjustable lock time delay (0s, 3s, 6s, 9s) and ultra-low power consumption, uses a coil that can work continuously at ultra-low temperatures, and is strong and durable, safe and eco-friendly. -
Page 5: Installation
Electric Bolt Lock Installation Guide V1.0.0 Internal Use Only Installation Prepare Installation Tools Screwdriver set (Phillips, torx bit) Used to secure the lock. Marker Used to mark holes. Tape measure Used to measure dimensions. Electric drill Used to drill holes. Insulation, waterproof tape Used to wrap the cable connection. -
Page 6: Install The Lock On A Wooden Door
Electric Bolt Lock Installation Guide V1.0.0 Internal Use Only 2.3.1 Install the Lock on a Wooden Door Close the door and draw a guide line along the top edge of the door on the top jamb. Mark mounting holes. Draw a line (line B) perpendicular to the guide line (line A) 5cm from the side jamb, and then draw the perpendicular bisector (line C) of the line B. - Page 7 Electric Bolt Lock Installation Guide V1.0.0 Internal Use Only Install the lock body. Put the lock body and faceplate into the holes and secure them with screws. Install the strike plate. Place the strike plate on top of the door with the bolt hole aligned with the bolt. ...
-
Page 8: Install The Lock On A Glass Door
Electric Bolt Lock Installation Guide V1.0.0 Internal Use Only 2.3.2 Install the Lock on a Glass Door Installation requirements: The lock shall be installed 5cm away from the side jamb. Ensure that the door is more than 3.8cm from the edge of top jamb when it is closed in place. ... - Page 9 Electric Bolt Lock Installation Guide V1.0.0 Internal Use Only Drill holes. Use a cutter to cut a 3mm deep hole for the faceplate. Reserve 2cm on the left and right sides of the faceplate hole for screws. Cut a deeper hole, about 45mm, in the faceplate hole with 2cm reserved on left and right.
-
Page 10: Install The Lock With A U-Bracket
Electric Bolt Lock Installation Guide V1.0.0 Internal Use Only Install the U-bracket and spacers. Place the two spacers in the U-bracket and mount the U-bracket to the door head. Close the door and move the bracket to align the hole with the bolt. ... - Page 11 Electric Bolt Lock Installation Guide V1.0.0 Internal Use Only Align the groove of the U-bracket with the top jamb, push the U-bracket upward until it fits the top jamb completely, and then tighten the black screws. Fix the bracket cover to the bracket and screw on the left and right sides. Insert the lock body into the bracket, lead the cables out through the cable hole on the cover, and then tighten the two screws on the left and right sides of the faceplate.
-
Page 12: Wiring
Electric Bolt Lock Installation Guide V1.0.0 Internal Use Only Wiring Wiring to face recognition access control devices (take ET-S33H 7-inch as an example) Wiring to access controllers (take ER-SR22 as an example) Zhejiang Uniview Technologies Co., Ltd. www.uniview.com 12/ 12...
Need help?
Do you have a question about the OEA-EL12 and is the answer not in the manual?
Questions and answers