Advertisement
Quick Links
Picnic table plans dimensions
Preparation
SHOPPING LIST
6 - 2x4 @ 8 feet long
9 - 2x6 @ 8 feet long
100 exterior screws, between 2-1/2" and 3" long (recommend star bit construction or
deck screws, #9)
CUT LIST
6 - 2x4 @ 30-7/8" long - both ends cut PARALLEL to each other at 22-1/2 degree angle
cut, long point to short point measurement - LEGS
3 - 2x4 @ 60-1/2" long - both ends cut NOT PARALLEL to each other, 22-1/2" degree
angle cut, long point to long point measurement - SEAT SUPPORT
3 - 2x4 @ 29-1/2" long - both ends cut NOT PARALLEL to each other, 22-1/2" degree
angle cut, long point to long point measurement - TABLE SUPPORT
Advertisement
Summary of Contents for ANAWHITE Long Picnic Table
- Page 1 Picnic table plans dimensions Preparation SHOPPING LIST 6 - 2x4 @ 8 feet long 9 - 2x6 @ 8 feet long 100 exterior screws, between 2-1/2" and 3" long (recommend star bit construction or deck screws, #9) CUT LIST 6 - 2x4 @ 30-7/8" long - both ends cut PARALLEL to each other at 22-1/2 degree angle cut, long point to short point measurement - LEGS 3 - 2x4 @ 60-1/2"...
-
Page 2: Cutting Instructions
2 - 2x4 @ 45-3/4" long - both ends cut PARALLEL to each other at 15 degree angle cut, long point to short point measurement - CROSS BRACE 9 - 2x6 @ 8 feet long (do not need to cut) CUTTING INSTRUCTIONS To fit all cuts on the 2x4s, start at the top of the cut list, and work down, only cut from a new 2x4 if you cannot fit the cut on scraps from earlier cuts. - Page 3 Instructions STEP 1 (/sites/default/files/2020- 07/best%20picnic%20table%20plans%20ana%20white%20step%201_0.jpg) Lay out two legs and one table support and line up carefully so top edges are flush, and bottom of legs are correct distance apart. Screw together with three screws and wood glue. TIP: Scrap wood pieces of 2x4s can be used to elevate the bottom of the legs so they sit flat while you work.
- Page 4 STEP 2 (/sites/default/files/2020- 07/best%20picnic%20table%20plans%20ana%20white%20step%202_0.jpg) Flip over and lay out the seat support. Attach to the legs with three screws per joint and glue. Build three leg sets identical.
- Page 5 STEP 3 (/sites/default/files/2020- 07/best%20picnic%20table%20plans%20ana%20white%20step%203.jpg) Mark the center of the seat supports and the table support. Attach one cross brace in between, centered, top edges flush.
- Page 6 STEP 4 (/sites/default/files/2020- 07/best%20picnic%20table%20plans%20ana%20white%20step%204.jpg) Mark center of remaining leg set seat support. Attach with the cross brace centered on the legs as shown.
- Page 7 STEP 5 (/sites/default/files/2020- 07/best%20picnic%20table%20plans%20ana%20white%20step%205.jpg) Lay the 2x6 boards down on top of the table and adjust. Side edges are flush, ends overhang 1- 1/2" or the width of a 2x4 scrap. Screw down with two screws per joint.
- Page 8 STEP 6 (/sites/default/files/2020- 07/best%20picnic%20table%20plans%20ana%20white%20step%206.jpg) Layout remaining 2x6 boards with even spacing in between. Screw down with two screws per joint.
Need help?
Do you have a question about the Long Picnic Table and is the answer not in the manual?
Questions and answers