Service Manual Model No.: CONTENTS Chapter 1.General Information 1-1. Document Information ................3 1-2. General Guidelines ................3 1-3. Important Notice ..................3 1-3-1. Follow the regulations and warnings ............. 3 1-3-2. Be careful to the electrical shock ............3 1-3-3.
Page 3
Service Manual Model No.: Chapter 6. Operation Instructions 6-1. Front Panel Controls ................27 6-2. Back Panel Controls ................27 6-3. Setting Up Your Remote Control ............28 Chapter 7. Electrical Parts 7-1. Block Diagram ..................29 7-2. Circuit Diagram ..................30 7-3. Wiring Connection Diagram ...............48 Chapter 8.
Service Manual Model No.: Chapter 1.General Information 1-1. Document Information Document format: Adobe PDF Author: Compiler: 1-2. General Guidelines When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
Service Manual Model No.: Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. The following techniques should be used to help reduce the incidence of component damage caused by electros static discharge (ESD).
Page 6
Service Manual Model No.: 1. Always unplug the receiver AC power cord from the AC power source before: a. Removing or reinstalling any component, circuit board module or any other receiver assembly. b. Disconnecting or reconnecting any receiver electrical plug or other electrical connection. c.
Service Manual Model No.: 12. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 13. Use only an anti-static type solder removal device. Some solder removal devices not classi¿ ed as "anti-static" can generate electrical charges suf¿ cient to damage ES devices. 14.
Service Manual Model No.: 1-4. How to Read this Service Manual 1-4-1. Using icons: Icons are used to attract the attention of the reader to specific information. The meaning of each icon is described in the table below: Note: A “note” provides information that is not indispensable, but may nevertheless be valuable to the reader, such as tips and tricks.
Service Manual Model No.: Chapter 3. Disassemble and Assemble Remove the Bottom Remove the Backcover Remove the Soundbox Remove the bracket of soundbox...
Page 15
Service Manual Model No.: Remove the powerboard,mainboard and signal board Remove the connection of bottom Remove the bracket of the powerboard,mainboard Remove the panel from front cabinet...
Service Manual Model No.: Chapter 4. Location of Controls and Components 4-1. Board Location Parts number Description Power Supply 0094001962 DC18K0E0C00M Mainboard Assembly(0090727319A) 0090726964 Signal Board 0094001254BG Panel 4-2.Mainboard of LD42K3 CNE3 CN21 CN17 CN27 CN25 CN14...
Service Manual Model No.: Speaker connectors (CN 27) Remote connectors (CN25) Pin number Pin number Description Signal name Signal name IRIN IR IN LEDR LED-RED LEDB LED-BLUE Keypad connector (CN14) Pin number Signal name Connector(Power for mainboard) (CN7) 3.3V Description Pin number Signal name KEY0...
Service Manual Model No.: LVDS Connector (CN5) Pin number Pin number Description Description Signal name Signal name ODSEL2 ODSEL2 ODSEL1 ODSEL1 PNL_SDA PNL_SDA PNL_CLK PNL_CLK BRI_IN BRI_IN PB-ADJUST PB-ADJUST LVDS Connector (CN2) Pin number Pin number Signal name Description Signal name Description 4-3.
Page 19
Service Manual Model No.: Signal name Pin number CN2(Power for mainboard) Signal name Pin number Pin number Signal name 12V(Audio Amplifier) E-PWM 12V(Audio Amplifier) PW-ON/OFF GND(Audio Amplifier) No Connection GND(Audio Amplifier) Back Light ON/OFF...
Service Manual Model No.: 4-4.LCD Panel 4-4-1. Function Description: Display the signal. 4-4-2. Connector de¿ nition LVDS: Symbol Description Symbol Description Ground ‘H’ or NC= 10bit(D) , ‘L’ = 8bit Bit Select No Connection R2AN SECOND LVDS Receiver Signal (A-) No Connection R2AP SECOND LVDS Receiver Signal (A+)
Page 23
Service Manual Model No.: PC/DVI AUDIO Y / VIDEO L - AUDIO - R PC IN COMPONENT / AV2 IN DSMB PC/DVI AUDIO Y / VIDEO L - AUDIO - R PC IN COMPONENT / AV2 IN DSMB SOURCE...
Page 24
Service Manual Model No.: PC/DVI AUDIO Y / VIDEO L - AUDIO - R PC IN COMPONENT / AV2 IN DSMB...
Page 25
Service Manual Model No.: Power source TO USE AC POWER SOURCE Use the AC polarized line cord provided for operation on AC. Insert the AC cord plug into a standard polarized AC outlet. Note ❏ Never connect the AC line cord plug to other than the specified voltage.
Service Manual Model No.: Chapter 6. Operation Instructions 6-1. Front Panel Controls TV/AV Press this key to open/close signal source 1 TV/AV options menu. Menu display. Press to access the on-screen 2 MENU menu display. Press to adjust the volume. In the MENU screen, 3 VOL +/- these buttons serve as right/left buttons.
Service Manual Model No.: 6-3. Setting Up Your Remote Control 1.POWER: Press this key to start TV from standby mode, press it again to return to standby mode. 2.USB: Press this key for quick switching of streaming media. 3.H. LOCK: Refer to the Functional Description on Page 23. 4.Press this key to open/close signal source options menu.
Service Manual Model No.: Chapter 8. Measurements and Adjustments 8-1. Service Mode 8-1-1.How to enter into Service Mode The way to the factory mode menu: Step 1: Press Menu, Step 2: Input 8893, Step 3: Press “OK” System will be into the factory mode menu when 3 steps above are done. 8-1-2.How to exit If you want to exit this factory menu, please press the button ”Exit”...
Service Manual Model No.: Chapter 9. Trouble shooting 9-1. Simple check Verify if the television is properly plugged Verify if the television is properly supplied power No picture/ No sound Verify if electricity is available. Verify if correct signals are input Press INPUT button to change signal input to TV input Blank screen Restart the television of power supply is interrupted...