Advertisement
5. OPERATION
5.1.
BEFORE FIRST USE
5.1.1.
Before using jack, purge hydraulic unit in order to eliminate any
air in the system. Place handle onto the release valve and
open the valve by turning the handle anti-clockwise, place the
handle back into the jacking socket and pump for 30 to 40
seconds (fig.1). When complete, close the release valve by
turning the valve nut clockwise.
5.1.2.
Place a few drops of hydraulic jack oil onto the pump piston
and pump the handle several times to distribute the oil.
5.1.3.
Thoroughly lubricate all moving parts.
5.2.
PREPARATION OF VEHICLE
WARNING! Before lifting ensure Section 1 safety instructions
‰
are read and understood.
5.2.1.
Prepare the vehicle as mentioned in the safety instructions
ensuring the ground on which the jack is to stand is level and
solid (not tarmacadam).
5.2.2.
Position the jack saddle under the vehicle manufacturer's
recommended lifting point.
5.3.
JACKING UP THE VEHICLE
5.3.1.
Close the release valve using the handle, turn clockwise (fig.1).
5.3.2.
Place the handle into the handle socket and commence pumping handle up and down using maximum strokes until the jack saddle
reaches the vehicle jacking point. Check the jacking point is centrally located on the saddle and raise the vehicle.
5.3.3.
Should the jack become overloaded, a safety excess pressure valve will open and stop the vehicle from lifting.
WARNING! The jack is a lifting device only and must not be used to support the load. Use correctly rated axle stands to support the
‰
load. When lifting a load of maximum capacity (1.5tonne) or close to it, it is recommended that the effort be reduced by the use of
assistance during this operation.
5.4.
LOWERING THE VEHICLE
WARNING! Ensure there are no persons or obstacles beneath the vehicle, or in the path of its descent.
‰
5.4.1.
If using axle stands, raise the jack high enough for the stands to be removed easily. Then place the handle onto the release valve nut
and turn anti-clockwise, very slowly, to open the valve.
5.4.2.
The lowering speed is controlled by the amount the handle is turned. Lower carefully, avoid any sudden changes in descent rate which
would shock load the hydraulic system.
6. MAINTENANCE
6.1.
When the jack is not in use, the ram should be in its lowest position to minimise corrosion. Remove the handle to deactivate jack.
6.2.
Keep the jack clean and lubricate all moving parts on a regular basis.
6.3.
Before each use, check for broken, cracked, bent or loose parts or any visible damage to ram, pump, saddle, lifting arm, frame and
all parts including nuts, bolts, pins and other fasteners. If any suspect item is found, remove jack from service and take necessary
action to remedy the problem.
DO NOT use the jack if believed to have been subjected to abnormal load or shock load.
8
6.4.
Periodically check the pump piston and the ram for signs of corrosion. Clean exposed areas with a clean oiled cloth.
6.5.
After one year the oil should be replaced in order to extend the life of the jack. Use hydraulic jack oil only.
IMPORTANT: Only fully qualified personnel should attempt hydraulic maintenance or repair.
6.6.
To check the oil level, lower the jack fully, remove oil filler plug (fig.1). The correct level is just below the bottom of the plug, if oil
level is low, fill as required.
NOTE: Use a good quality jack oil, such as SEALEY HYDRAULIC JACK OIL.
WARNING: DO NOT use brake fluid, or any fluid other than hydraulic jack oil as this may cause serious damage to the jack and will
‰
invalidate the warranty!
6.7.
When draining the oil make sure that no dirt is allowed to enter the hydraulic system.
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THIS PRODUCT.
Ensure hydraulic products are only repaired by local service agents. There are service/repair agents in all parts of the UK.
9
DO NOT return jacks to us. Please telephone us on 01284 757500 to obtain the address and 'phone number of your local stockists.
8
If jack is under guarantee contact your local Sealey stockist.
De-commissioning the Jack. Should the jack become completely unserviceable and require disposal, draw off the oil into an
approved container and dispose of the jack and the oil according to local regulations.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk or 01284 757505. Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
01284 703534
sales@sealey.co.uk
Original Language Version
Fig.1
www.sealey.co.uk
1015CX.V2 | Issue 3 (3,4,F) 29/05/19
Advertisement
