Related Manuals for Paugge ENT-SDVoECON
Summary of Contents for Paugge ENT-SDVoECON
- Page 1 Paugge ENT-SDVoECON User Manual ENT-SDVoECON AV over IP Network Controller User Manual Version 4.0 www.paugge.com...
-
Page 2: Table Of Contents
Paugge ENT-SDVoECON User Manual Thank you for purchasing this product For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. Surge protection device recommended This product contains sensitive electrical components that may be damaged by electrical spikes, surges, elec- tric shock, lighting strikes, etc. -
Page 3: Introduction
Paugge ENT-SDVoECON User Manual 1.0 Introduction This AV over IP Controller is used to control and manage ENT-SDVoE10G Transceivers. Dual LAN ports pro- vides network isolation of Control and Multicast video distribution network. Built-in Web GUI, TCP and RS- 232 control are supported. It supports POE and wide band 12V IR signal receiving. -
Page 4: Operation, Controls And Functions
Paugge ENT-SDVoECON User Manual 5.0 Operation, Controls and Functions 5.1 Front Panel Power Status Update Reset 1. Reset Button - Press and hold for approximately 10 seconds until the status LED starts to flash, the controller will automatically reset. 2. Power LED - Illuminates red when power in applied. -
Page 5: Infrared Pin Connections
Paugge ENT-SDVoECON User Manual 5.3 IR Pin Connections 6.0 Web GUI 6.1 Preparation The controllers Web GUI gives you complete control of encoders and decoders within your LAN/Project. Step 1: Enter controllers URL or IP address in to your Web Browser address bar. - Page 6 Paugge ENT-SDVoECON User Manual Stage 2: Click the “close” button to load an existing project directly in to the web page or click the “next” but- ton to create a new project. To setup AV over IP system, you need to set the IP management mode of the video LAN domain. The IP management modes are: ●...
-
Page 7: Network Settings - Mode 1, Automatically Managed By Controller
Paugge ENT-SDVoECON User Manual 6.2 Mode 1: Automatically managed by the controller box. Multiview DVD Player TX GND RX TX GND RX TX GND RX TX GND RX TX GND RX TX GND RX HDMI IN HD MI OUT DC 12V... - Page 8 Paugge ENT-SDVoECON User Manual If you select “Automatically add Encoders and Decoders to project” and click the “Scan” button to enter the project page. All discovered devices will be listed in the current devices page. AVoIP Project Display ID Save Project...
- Page 9 Paugge ENT-SDVoECON User Manual Click “Stop Scan” to stop search. Then the “Add All” buttons and “Add” buttons behind Unassigned Encoders and Unassigned Decoders in the figure below will become operable. AVoIP Project Unassigned Devices Configuration & Scan Stop Scan...
-
Page 10: Network Settings - Mode 2, Dhcp
Paugge ENT-SDVoECON User Manual 6.3 Mode 2: DHCP Mode - Please connect all devices according to the diagram below. Multiview DVD Player TX GND RX TX GND RX TX GND RX TX GND RX TX GND RX TX GND RX... -
Page 11: Network Settings - Static Ip
Paugge ENT-SDVoECON User Manual 6.4 Mode 3: Static IP mode Multiview DVD Player TX GND RX TX GND RX TX GND RX TX GND RX TX GND RX TX GND RX HDMI IN HD MI OUT DC 12V Video LA N (PoE ) - Page 12 Paugge ENT-SDVoECON User Manual After entering the interface as shown in the dialogue box below, manually set the IP address, subnet mask and gateway for the video LAN. Controller Box Video LAN Port Settings IP Address 169.254.2.225 Subnet Mask 255.255.0.0 Gateway 169.254.2.1...
-
Page 13: System Control
Paugge ENT-SDVoECON User Manual On this interface, you can set the IP address range of Encoders and Decoders. After the setting is complete, click the “Next” button to enter the interface as shown in the figure below. Now you can select to automatically add all discovered Encoders and Decoders to the project or just them in the web page where you can add them manually. -
Page 14: Matrix Control
Paugge ENT-SDVoECON User Manual 7.2 Matrix Control AVoIP Matrix Control Encoders Encoder 001 Encoder 002 Decoders Decoder 001 Decoder 001 Decoder 001 Decoder 001 TX: Encoder 001 TX: Encoder 002 TX: Encoder 003 TX: Encoder 004 Encoders: Display all the current Encoders. The text in the figure is the name of the device. -
Page 15: Project
Paugge ENT-SDVoECON User Manual 7.3 Project Page AVoIP Project Display ID Save Project Clear Project Current Devices Encoders Encoders Name IP Address Status Name IP Address Status Encoder 001 169.254.3.6 Offline Decoder 001 169.254.6.8 Offline Encoder 002 169.254.3.1 Offline Decoder 002 169.254.6.5... -
Page 16: Encoders
Paugge ENT-SDVoECON User Manual 7.4 Encoders AVoIP Encoders Refresh Name MAC Address IP Address Firmware Status EDID Audio Selection > Encoder 001 6C:DF:FB:00:09:71 169.254.3.5 1.00.21 Online Default EDID HDMI > Encoder 002 6C:DF:FB:00:09:72 169.254.3.1 1.00.21 Online Default EDID HDMI >... - Page 17 Paugge ENT-SDVoECON User Manual AVoIP Encoders Refresh Name MAC Address IP Address Firmware Status EDID Audio Selection > Encoder 001 6C:DF:FB:00:09:71 169.254.3.5 1.00.21 Online Default EDID HDMI Name Encoder 001 Update ID Select CEC Pass-Through Power LED Copy EDID Select a Decoder...
-
Page 18: Decoders
Paugge ENT-SDVoECON User Manual 7.5 Decoders AVoIP Decoders Refresh Name MAC Address IP Address Firmware Status Source Function Scaler Resolution Online Matrix > Decoder 001 6C:DF:FB:00:09:97 169.254.6.6 1.00.21 Encoder 005 Pass Through Pass Through Matrix > Decoder 002 6C:DF:FB:00:09:92 169.254.6.7 1.00.21... - Page 19 Paugge ENT-SDVoECON User Manual AVoIP Decoders Refresh Name MAC Address IP Address Firmware Status Source Scaler Resolution Function Decoder 001 6C:DF:FB:00:09:97 169.254.6.6 1.00.21 Online Encoder 005 Pass Through Matrix Name > Decoder 001 > Update ID Select CEC Pass-Through >...
-
Page 20: Locked Signal Routing
Paugge ENT-SDVoECON User Manual 7.6 Locked Signal Routing AVoIP Locked Signal Routing Help Refresh Name IP Address Video Audio Serial Decoder 001 169.254.6.25 Follow Follow Follow Follow Follow Follow Decoder 002 169.254.6.35 Follow Follow Follow Follow Follow Follow Decoder 003 169.254.6.30... - Page 21 Paugge ENT-SDVoECON User Manual Step 1: Click “Create” to reveal the following window. Create a new Video Wall Video Wall ID Name Video Wall 1 Horizontal Vertical You can set the Video Wall ID, Name, Horizontal and Vertical panel numbers.
- Page 22 Paugge ENT-SDVoECON User Manual Step 3: Click “Class Configuration” to enter the class configuration page, then click each screen to select the corresponding Class as required (the same class name will form a video wall, you can create a regular or irreg- ular video wall by Class Configuration).
- Page 23 Paugge ENT-SDVoECON User Manual On this page, you can select different video walls and configurations that you have set up by clicking the drop- down box on the right of “Video Wall Selection / Configuration Selection”. Besides, you can directly drag En- coders at the top of the page to the video wall to change signal sources.
-
Page 24: Multiview Management
Paugge ENT-SDVoECON User Manual 7.8 Multiview Management AVoIP Multiview Management Multiview Layout Encoder List Decoders Configuration Apply Reset Reset All Config 4 On this page, you can create and configure Multiview as required. Please follow below steps to create a multi- view. - Page 25 Paugge ENT-SDVoECON User Manual Step 2: Drag Encoders from the Encoder List to the Multiview Layout respectively, then click the “Apply” but- ton. AVoIP Multiview Management Multiview Layout Encoder List Decoders Configuration Apply Reset Reset All Config 4 Step 3: After configuration, you can switch to “Multiview Control” page for video preview, as shown in be- low.
- Page 26 Paugge ENT-SDVoECON User Manual If you want to delete a multiview, just click the “Reset” button. A prompt window will pop up and you can de- lete it after clicking “Yes”. AVoIP Multiview Management Multiview Layout Encoder List Decoders Configuration...
-
Page 27: Users
Paugge ENT-SDVoECON User Manual 7.9 Users AVoIP Users Help New User Refresh Encoders IDs Decoder IDs There are no users in the system On this page you can setup user accounts. 7.10 Controller Settings AVoIP Controller Settings Reset Controller Update... -
Page 28: Firmware Update
Paugge ENT-SDVoECON User Manual 7.11 Firmware Update AVoIP Firmware Update Upload Firmware Upload Encoder or Decoder Firmware Update SS Firmware Show Progress Update Firmware Encoders Decoders Update All Update All ID Name SS Firmware Firmware ID Name Firmware Encoder 001 1.02.15... -
Page 29: Maintenance And Warranty
Paugge ENT-SDVoECON User Manual 8.0 Maintenance Clean this unit with a soft, dry cloth. Never use alcohol, pint thinner of benzene to clean these devices. Servicing Damage requiring service: This product should be serviced by a qualified service engineer if: ●... - Page 30 Paugge ENT-SDVoECON User Manual Limited warranty limits and exclusions This Limited Warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage. The Limited Warranty ALSO DOES NOT COVER damag-...