Other Play Methods - Panasonic SL-SW205 Operating Instructions Manual

Other Play Methods —
The letters such as @ in the various illustrations refer to the descriptions in the "Location of Controls" (see page 2) section.
Skip play
The disc plays from the specific track through to the end, then
play stops automatically.
Preparation: Put unit in stop mode.
1. MODE :NORMAL:
© RESUME } I $ RANDOM
2 Select the desired track.
Pi
hed
©» IOs)
ty = 4 *SKIP)m SEARCH
G
&3
Random play
1 MORT rabu
—
2
© CR
© RESUME I 4'4 RANDOM
For your reference:
aIt is also possible to press the >] button while the unit is in
stop status to change the first track to be played. {All tracks are
played eventually, regardless of which is played first.)
¢Program play is not possible in the random mode.
Resume play
This function allows you to listen from the beginning of the track
where play stopped because the unit was powered off (or
switched to stop status). It is useful when listening to CDs in the
caf, erc: MODE NORMAL
RESUME I 1 | RANDOM
©
djm
Release
MODE NORMAL?
© RESUME 1 $ 8 RANDOM
For your reference:
sIf the MODE (play mode) slider is put in the RESUME position,
the all-repeat function will be activated automatically as soon as
the unit is powered on.
sIf power is cut off near the end of a track (power off status),
playback may resume from the beginning of the next track in
some cases.
èlf the unit is powered off while a disc was playing and then a
new disc is inserted, play wilt begin from the middle of the new
disc because the unit remembers the position where play
stopped on the old disc.
Program play
Up to 24 tracks can be entered in the programmed sequence.
Preparation: Put unit in stop mode.
D
Select the desired track.
N
Pi
tea
@ 2) Qs
1 2 SKIP j/w SEARCH
Register in sequence,
(The indication "M" and the programmed sequence ap-
pear on the display panel.}
MEMORY}
RECALL
O
Ww
= Repeat steps 2 and 3 to program all the
desired tracks.
o CN
@ To program the same track in the sequence more
than once
After step 3, press MEMORY/RECALL the desired number of
times.
ol
@ ií "Ff" is displayed
No more tracks may be added to the sequence.
@ To confirm the contents of the programmed se-
quence
Press MEMORY/RECALL while the disc is playing. (The num-
ber of the programmed tracks appear on the display panel in se-
quence.)
m To delete the entire programmed sequence
Press B, POWER OFF.
Repeat function
Press REPEAT while disc is playing or when unit is in stop
status,
REPEAT
j by
The setting is switched in the sequence indicated below each time
REPEAT is pressed.
1-track repeat (1 œ)
One track is repeated.
4
All-track repeat (ALL œ>)
All the tracks on the disc are repeated.
Cancel
For your reference:
If REPEAT is pressed during program play, only the tracks in the
programmed sequence are repeated.
(The indication "ALL" is not displayed.)
Changing the sound quality
{This function is available except when using the OUT jack.)
-SW205/SL-SW405/SL-SW411C
XBS ON:
Select this setting to boost the low-range response.
OFF 1008
D
Select this setting to tum off the XBS function.
XBS
Of 1 — 40N
US
Select this setting to boost the low range response.
<XBS:— VMSS
OFF oh |
ZI
VMSS:
Boosts the low frequency range. Also, the vibration of the ear-
pieces of the included headphones makes sound vigorous.
Raising the volume level makes the VMSS effect intensify.
.XBS — <VMSS>
OFF a 0
z
OFF:
Select this setting to turn off the XBS and VMSS functions.
XBS VMSS
Gs o
IS
Notes
*VMSS may not be effective depending on the source.
sIf you experience a ringing or discomfort in your ear while lis-
tening in VMSS made, reduce volume or tum the VMSS mode
OFF.