Advertisement

Quick Links

OWNER'S MANUAL
LG LED Signage
(LED SCREEN)
Please read the safety information carefully before using this product.
After reading this manual, keep it in an easily accessible location for future reference.
LSAB009-M15
LSAB009-S15
LSAB009-N15
LSAB009-T15
LSAB009-U15
LSAB009-Q15
LSAB009-M23
LSAB009-S23
LSAB009-N23
Copyright © 2023 LG Electronics Inc. All Rights Reserved.
LSAB009-T23
LSAB009-U23
LSAB009-Q23
www.lg.com

Advertisement

Table of Contents
loading

Summary of Contents for LG LSAB009-M15

  • Page 1 Please read the safety information carefully before using this product. After reading this manual, keep it in an easily accessible location for future reference. LSAB009-M15 LSAB009-T15 LSAB009-M23 LSAB009-T23 LSAB009-S15 LSAB009-U15 LSAB009-S23 LSAB009-U23 LSAB009-N15 LSAB009-Q15 LSAB009-N23 LSAB009-Q23 www.lg.com Copyright © 2023 LG Electronics Inc. All Rights Reserved.
  • Page 2: Table Of Contents

    - Remove Protective Bracket ........ 17 - Installation Precautions Guide ......19 - Installation Location ..........21 - Terminal ................. 23 CONNECTING LAN (LSAB009-M15, Q15, N15, U15, M23, Q23, N23, U23) ..... 24 CONNECTING AC (LSAB009-M15, N15, M23, N23) ......... 25 TROUBLESHOOTING ....
  • Page 3: Safety Precautions

    SAFETY PRECAUTIONS The safety precautions are intended to prevent unexpected danger or harm by helping the user to use the product safely and for its intended purpose. WARNING If you ignore the warning message, you may be seriously injured or there is a possibility of accident or death. CAUTION If you ignore the caution message, you may be slightly injured or the product may be damaged.
  • Page 4: Precautions For The Ac Cable And Power

    Precautions for the AC Cable and Power WARNING • Before using an AC cable, make sure it conforms to the national standards. • Operate the display only from a power source (i.e. voltage) indicated in the product specification. - Otherwise the product can be damaged, fire can occur or you may be electrocuted. If you are not sure what type of power supply you have, consult a certified installation company.
  • Page 5 • If water or any foreign substance enters the product, disconnect the AC cable immediately and contact the service centre. - Otherwise, this may cause a fire or electric shock due to damage to the product. • Keep the AC cable away from heating devices. - The cord coating may melt and cause fire or electric shock.
  • Page 6: Precautions For Moving The Product

    Precautions for Moving the Product WARNING • Contact the service centre before moving the product. - It may cause electric shock and damage the product. • Make sure the product is turned off, unplugged, and all cables have been removed before the product is moved. - You may be electrocuted or the product can be damaged.
  • Page 7: Precautions For Installing The Product

    Precautions for Installing the Product WARNING • Contact the service centre before installing the product. - It can cause electric shock and damage the product. • Do not drop an object on or impact on the product. Keep out of reach of children and do not place toys or objects near the product to prevent throwing things on the product screen.
  • Page 8 CAUTION • Install the product where no Electromagnetic Interference occurs. • If you install the product in a place that does not meet the recommended conditions, this may cause serious damage to the product’s picture quality, life cycle, and appearance. Please check with service engineer before installing. Please do not install the product in places such as where there is an abundance of fine dust or oil mist, chemical substances are used, exposed to direct sunlight, the temperature is very high or low, the humidity is very high.
  • Page 9: Precautions For Cleaning The Product

    Precautions for Cleaning the Product WARNING • Keep the product clean at all times. - If you don’t clean the unit for a long time and it becomes covered in dust, it can cause fire or product damage. • When you need to clean the inside of the product, you must contact the service centre. - Otherwise, cleaning without support may cause a fire, electric shock, or damage to the product.
  • Page 10: Precautions For Using The Product

    Precautions for Using the Product WARNING • Do not use the product in any environment with excessively high temperatures or humidity. - It may cause electrical shock or damage the product. • If you use the product for a long period of time, take a rest from time to time to protect your vision. - Extended viewing could result in impaired vision.
  • Page 11 • Do not use high voltage electrical goods near the product (e.g., a bug zapper). - This may result in product malfunction if it receives an electrical shock. • If there is a gas leak, do not touch the outlet, and open the windows for ventilation. - Otherwise, the product may cause fire or electric shock.
  • Page 12: Product Disposal

    Product Disposal • Do not dispose of this product with general household waste. • Disposal of this product must be carried out in accordance to the regulations of your local authority.
  • Page 13: Assembling And Preparing

    ASSEMBLING AND PREPARING CAUTION • Always use genuine components to ensure safety and durability of the product. • The product warranty will not cover damage or injury caused by the use of unauthorised components. NOTE • The accessories provided with your product may vary depending on the model or region. •...
  • Page 14: Optional Accessories

    Without prior notice, optional accessories are subject to change to improve the performance of the product, and new accessories may be added. The illustrations in this manual may differ from the actual product and accessories. Middle Frame KT-BZ1080 Wall Mount WM-LC2 WM-LC3 WM-LC4 WM-LS2 WM-LS3 WM-LS4 Frame Jig WM-LG...
  • Page 15: Handling For Protecting Led Package Screen

    Handling for Protecting LED Package Screen When taking out the product, make sure the screen is not pressed. Protection Pad To stand the product upright, hold it on both sides so that the LED package screen does not touch the floor. LED Package Screen...
  • Page 16 Place the product with the LED package screen facing down. To protect the screen, lay the protective pad in the box on the floor. LED Package Screen Protection Pad If you do not have a pad, make sure that there is no foreign object on the floor when you lay the product on the floor, and then carefully place the LED package screen facing down or up.
  • Page 17: Remove Protective Bracket

    Remove Protective Bracket Before installing the product, disassemble the protective brackets attached to each edge. M4 x L8 NOTE • Keep the protective brackets because you need them to move the product again.
  • Page 18 CAUTION If the product is tilted towards the LED package screen after the brackets on the corners are removed, the bottom of the product may be damaged. LED Package Screen If the product is tilted towards the edge of the LED package screen after the brackets on the corners are removed, the bottom (corner) of the product may be damaged.
  • Page 19: Installation Precautions Guide

    Installation Precautions Guide Temperature • Make a cooling system for the enclosure so that the operating temperature of the product can be maintained. - Product operating temperature: 0 °C to 40 °C (the recommended room temperature is below 25 °C.) • Install in a location where the warm air from an air conditioner does not directly affect the product. - This will prevent malfunctions such as the screen turning off.
  • Page 20 Installation Position • Ensure the distance from the ceiling of the installation room to the product is at least 400 mm. - The high temperature air collected at the ceiling will naturally circulate to prevent malfunction. • Ensure the distance from the floor of the installation room to the product is at least 100 mm. - The air from the floor will easily circulate to the ceiling to prevent malfunctions. E : 400 mm or more F : 100 mm or more...
  • Page 21: Installation Location

    Installation Location Installing on a Wall A : 30 mm or more (recommended) - Can be installed directly on our own wall mount without using a structure. (see example) B : 25 mm or more C : 60 mm or more Installing on a Recessed Wall • After installation on a recessed wall, a bezel can be installed for interior purposes. A : 30 mm or more (recommended) - Can be installed directly on our own wall mount without using a structure.
  • Page 22 • Example - Depending on the model, the shape of the wall mount may difference. Wall mount usage scene Wall mount and structure usage scenes When Installing the Bezel • Ensure it can be detached for product repair. • For the top / bottom bezels, secure at least 60 % of the air vent to facilitate air circulation. - This will prevent malfunction.
  • Page 23: Terminal

    Terminal LSAB009-M15, N15, M23, N23 LSAB009-U15, Q15, U23, Q23 • : Sends the IR signal to another set. • : Sends the LAN signal to another set. NOTE • The IR sensor is not provided with this product. • For System Controller the IR sensor and remote control are provided.
  • Page 24: Connecting Lan (Lsab009-M15, Q15, N15, U15, M23, Q23, N23, U23)

    CONNECTING LAN (LSAB009-M15, Q15, N15, U15, M23, Q23, N23, U23) You can connect to the System Controller by using an LAN cable. LAN cable (*Not provided) System Controller System Controller LED Screen CSAB-00915D, CSAD LSAB009-*15 CSAB-00914, CSAD LSAB009-*23 CAUTION •...
  • Page 25: Connecting Ac (Lsab009-M15, N15, M23, N23)

    CONNECTING AC (LSAB009-M15, N15, M23, N23) You can connect the unit to a power disconnecting device using an AC cable. • Use the AC cable to connect to the power disconnecting device. (Please use a cable that is long enough to be connected to the screen.)
  • Page 26 Country Live Neutral Ground Europe Brown Blue Green & Yellow North America Black White Green & Yellow India Black Green & Yellow Japan / Taiwan Black White Green & Yellow Korea Brown Blue Green & Yellow You can connect the AC cable connected to the power disconnecting device to the screen. Structure Fixing parts 100 mm...
  • Page 27: Troubleshooting

    TROUBLESHOOTING No image is displayed. • Is the AC cable connected to the product? - Make sure the AC cable is properly connected to the power disconnecting device. • Is the ‘No Signal’ message displayed? - There is no connection between System Controller and the input source. Check the connection status of the LAN cable.
  • Page 28 Without prior notice, the software is subject to change to improve the functionality of the product. • The above items are only applicable to the LSAB009-M15, Q15, N15, U15, S15, T15, M23, Q23, N23, U23, S23, T23 model. Please read “TROUBLESHOOTING” in the manual of System Controller.
  • Page 29: Product Specifications

    Without prior notice, the product specifications are subject to change to enhance the functionality of the product. symbol means alternating current, and the symbol means direct current. LSAB009-M15, Q15, N15, U15, M23, Q23, N23, U23 Pixel pitch (distance between pixels) 0.9375 mm Resolution 640 x 360...
  • Page 30 LSAB009-S15, T15, S23, T23 Pixel pitch (distance between pixels) 0.9375 mm Resolution 640 x 360 Pixel density 1,137,778 pixels/m Number of pixels per screen 230,400 pixels Number of colour output bits Internal 20 bit Number of expressible colours 4.398 x 10 Input/ Output ports Not Applied LSAB009-S15, S23 600 mm x 337.5 mm x 44.9 mm / 6.8 kg Dimensions (Width x Height x Depth) / Weight LSAB009-T15, T23...
  • Page 31 (Unit: mm) 337.5 44.9...
  • Page 32 The model and serial number of the product are located on the back and on one side of the product. Record them below in case you ever need service. MODEL Temporary noise is normal when powering ON or OFF this device.

Table of Contents