Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Matsusada Precision PZJE Series
- Page 1 Instruction Manual PZJE series MODEL *037.9.094* B/N 037.9.094 Rev. 0.2...
- Page 2 No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, or by any means, mechanical, electronic, photocopying, recording, or otherwise, without the prior written permission of Matsusada Precision. No patent liability is assumed with respect to the use of the information contained herein.
- Page 4 Bistable push button switch for preventing electric shock) Indicates the possible danger of death if Bistable push button switch you drink it and burns or blindness if it attaches. Indicates the possible danger of exposure Alternative Current to radiation. Matsusada Precision PZJE series...
- Page 5 It may result in electric shock or fire. Regarding the input voltage Check the page describing the input terminals and input voltage in the instruction manual. Do not provide any voltage out of the specifications. Matsusada Precision PZJE series...
- Page 6 In order to avoid electric shock, ground the terminals to discharge using a short-circuit grounding apparatus and check the voltage again. The terminals here mean all terminals like input and output terminals and terminals for communications and remote controls. Matsusada Precision PZJE series...
- Page 7 It requires to be replaced at regular intervals to extend the lifetime. For the replacement, contact us. (It requires a replacement charge separately. Do not replace it by yourself, as there is a risk of electric shock.) Matsusada Precision PZJE series...
-
Page 8: Table Of Contents
Table of Contents Page Introduction ..............................1 Greetings ............................... 1 Unpacking .............................. 1 Installation Conditions ........................... 1 Precautions for Handling ........................2 Troubleshooting ............................. 2 External Appearance ............................ 3 Front Panel ............................3 Rear panel ............................. 4 Instruction for Handling ..........................5 Overview .............................. -
Page 10: Introduction
1 Introduction Greetings Thank you very much for your purchase of Matsusada Precision piezo driver. This Instruction Manual was written to provide the user with instructions on the safe operation of our piezo driver. Matsusada Precision takes every precaution to ensure the quality of our products. Please refer carefully to this manual in order to use this product correctly and safely, and to achieve the best possible performance. -
Page 11: Precautions For Handling
1. Check whether the specified voltage is input. ・ Power supply voltage: 100V to 240V AC±10% 50/60 Hz single phase ・ External input voltage: -10V to 10V 2. Check whether or not the overcurrent protection (OCP) is working. (See [3-4 Protections].) Matsusada Precision PZJE series... -
Page 12: External Appearance
2 External Appearance Front Panel (1) POWER ON/OFF switch (2) OUTPUT ON/OFF switch (3) Output voltage meter 3½ digits (4) Output voltage monitor connector (5) Vcon-in connector (6) Bias voltage ON/OFF switch (7) Bias voltage setting dial Matsusada Precision PZJE series... -
Page 13: Rear Panel
(2) GROUND terminal (3) FUSE (5A) (4) AC input connector (100V - 240V) (5) Clamp for AC input cable (6) Terminal block for options (-LS option) Dimension: 280 W x 124 H x 430 D (mm) Matsusada Precision PZJE series... -
Page 14: Instruction For Handling
≦ the rated output current the average current I current ≦10msec should be required. If used beyond these conditions, the output may be stopped. (See [3-4 Protections].) Output current Model Rated voltage Ip [A] ±150 PZJE-0.15B 0.75 ±300 PZJE-0.3B Matsusada Precision PZJE series... -
Page 15: Operation
At the same time, the indicator of the OUTPUT ON/OFF switch turns off. To reset it, turn OFF the POWER ON/OFF switch and then ON again. Matsusada Precision PZJE series... -
Page 16: Options
Open collector can be used instead of switch. Using open collector remote control operation -LS function will not work if (1) and (2) are Not using remote switch operation connected with the supplied short hardware. Short S.G. Signal Ground Matsusada Precision PZJE series... -
Page 17: Overload Protection By Dropping (-Lc)
105% of its rated maximum. As the overcurrent state is canceled, the output voltage will be resumed from the drooping state. Matsusada Precision PZJE series... - Page 18 Revision History Rev. No. Rev. Date Rev. Description 2022/01 First edition (as the English version)
Need help?
Do you have a question about the PZJE Series and is the answer not in the manual?
Questions and answers