Summary of Contents for Matsusada Precision RMO Series
- Page 1 Instruction Manual RMO series MODEL 19-inch Rack Mount Holder *174.9.020* B/N 174.9.020 Rev. 1.6...
- Page 2 ◆ No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, or by any means, mechanical, electronic, photocopying, recording, or otherwise, without the prior written permission of Matsusada Precision. ◆ No patent liability is assumed with respect to the use of the information contained herein.
-
Page 3: Table Of Contents
4-3-1 AC Wire Harness of RMO-133H-RK2/RK3 ................... 22 4-3-2 Fan Cable of RMO-133H-RK2 ......................23 4-3-3 Fan Cable of RMO-133H-RK3 ......................23 4-3-4 Installing Fan Unit ..........................25 4-3-5 Installing Rack Mount Cover of RMO-133H-RK/RK2/RK3 ..............25 4-3-6 Wiring Fan Unit of RMO-133H-RK/RK2/RK3 ..................26 RMO series... - Page 4 Page 5 Accessories ............................27 5-1 Blank Panel............................. 27 5-2 Installing Blank Panel ..........................27 5-2-1 RMO-133H-RK/RK2/RK3 (RK-80/R4K-80/R4K-36 series ) ..............28 5-2-2 RMO-133H-RK400 (RK series: 400W/800W/1200W) ................28 5-2-3 RMO-133H-CO (CO series) ........................28 5-2-4 RMO-150H-B (ES series) ........................29 5-2-5 RMO-133H-DRJ (DRJ series) .......................
-
Page 5: Introduction
1-2 Overview The RMO series is a rack mount adapter for our tabletop power supplies, electronic loads, and digital controllers in a 19-inch rack. The product is specially designed in accordance with Matsusada products to be installed, so it can be easily used for installing them without measures against heat generation. -
Page 6: Lineup
*6: To increase the air flow, make space more than 10 cm. But, if it cannot be allocated, install a forced cooling system. *7 As EGD series can operate as a charge/discharge system combined with RK series (400W/800W/1200W), they can be mixed and stored compactly in the holder. RMO series... -
Page 7: Before Use
When attaching the power supply unit to the rack mount, do not use longer screws than 8 mm in length. ・ Use the screws (M3 x 8) supplied for the plastic feet for installation. ・ However, as for REKJ series, use the supplied pan-head screws (M3 x 8) for it. RMO series... -
Page 8: External Appearance
RK(800W): 2 units and Blank panel 140W: 1 piece (*Up to 3 units are available.) RK series (1200W) RK(1200W): 1 unit and Blank panel 210W: 1 piece (*Up to 2 units are available.) (1) JIS pitch hole (3) Blank panel (sold separately) (2) EIA pitch hole (4) Handles RMO series... - Page 9 DRJ500: 2 units and Blank panel 140W: 1 piece (*Up to 3 units are available.) REKJ series REKJ: 1 unit and Blank panel 210W: 1 piece (*Up to 2 units are available.) (1) JIS pitch hole (3) Blank panel (sold separately) (2) EIA pitch hole RMO series...
- Page 10 R4G: 3 units and Blank panel 84W: 2 pieces (*Up to 5 units are available.) EGD series EGD: 3 units and Blank panel 84W: 2 pieces (*Up to 5 units are available.) (1) JIS pitch hole (3) Blank panel (sold separately) (2) EIA pitch hole RMO series...
-
Page 11: External Dimensions
3 External Appearance 3-2 External Dimensions 3-2-1 RMO-133H-RK/-RK2/-RK3 (RK-80/R4K-80 series) Rear view RMO series... -
Page 12: Rmo-133H-Rk/-Rk2/-Rk3 (R4K-36 Series)
3 External Appearance 3-2-2 RMO-133H-RK/-RK2/-RK3 (R4K-36 series) Rear view RMO series... -
Page 13: Rmo-133H-Rk400 (Rk Series 400W/800W/1200W)
3 External Appearance 3-2-3 RMO-133H-RK400 (RK series 400W/800W/1200W) RMO series... -
Page 14: Rmo-133H-Co (Co Series)
3 External Appearance 3-2-4 RMO-133H-CO (CO series) RMO series... -
Page 15: Rmo-150H-B (Es Series)
3 External Appearance 3-2-5 RMO-150H-B (ES series) RMO series... -
Page 16: Rmo-133H-Drj (Drj Series)
3 External Appearance 3-2-6 RMO-133H-DRJ (DRJ series) For DRJ500-LNh RMO series... -
Page 17: Rmo-44H-Half (Rekj Series)
3 External Appearance 3-2-7 RMO-44H-HALF (REKJ series) RMO series... -
Page 18: Rmj-150H-Ejc (Ejc Series)
3 External Appearance 3-2-8 RMJ-150H-EJC (EJC series) RMO series... -
Page 19: Rmo-133H-Epr (Epr Series)
3 External Appearance 3-2-9 RMO-133H-EPR (EPR series) RMO series... -
Page 20: Rmo-177H-R4G (R4G Series)
3 External Appearance 3-2-10 RMO-177H-R4G (R4G series) RMO series... -
Page 21: Installation And Connection
For details about how to remove it, see [4-3-5 Installing Rack Mount Cover of RMO-133H-RK/RK2/RK3]. *Align the rear side of the power supply unit with the holes in the orange circle parts in the figure below, and tighten the pan-head screws. RMO series... -
Page 22: Rmo-133H-Rk/-Rk2/-Rk3 (R4K-36 Series)
For details about how to remove it, see [4-3-5 Installing Rack Mount Cover of RMO-133H-RK/RK2/RK3]. 4-2-3 RMO-133H-CO (CO series) Mount the product by fixing the two parts as follows. *As for RMO-133H-CO (CO series), use the supplied two pan-head screws (M3 x 6) per CO series unit. RMO series... -
Page 23: Rmo-133H-Rk400 (Rk Series 400W/800W/1200W)
On the rear side, insert the spacer (φ3x5) between the rack and the CO series main unit, and mount the product using the flat-head screws (M3 x 10). *CO series 1 unit / RK(400W) series 3 units (Example): CO-G32m: 1 unit, RK(400W): 3 units, Blank panel 35W: 1 piece, Blank panel 70W: 2 pieces RMO series... -
Page 24: Rmo-150H-B (Es Series)
4 Installation and Connection 4-2-5 RMO-150H-B (ES series) Mount the product by fixing in four parts as follows. 4-2-6 RMO-133H-DRJ (DRJ series) Mount the product by fixing in four parts as follows. RMO series... -
Page 25: Rmo-44H-Half (Rekj Series)
4 Installation and Connection 4-2-7 RMO-44H-HALF (REKJ series) Mount the product by fixing in four parts with the supplied flat-head screws as follows. Attach the supplied display seal for input/output terminal to the power supply unit as shown below. RMO series... -
Page 26: Wiring Rmo-133H-Rk/Rk2/Rk3
Unplug the 8-pin connectors according to number of units, and attach the dedicated cables there. Insert the plugs into the sockets until they lock. (See the red circle in the figure below.) For safety, keep unused plugs inserted, as shown below. RMO series... -
Page 27: Fan Cable Of Rmo-133H-Rk2
Unplug the 6-pin connector, and attach the fan unit wires. Insert the plug into the socket until it locks. 4-3-3 Fan Cable of RMO-133H-RK3 (1) Remove the two 4-pin and 6-pin plugs coming out of the connectors on the switch. RMO series... - Page 28 4 Installation and Connection (2) Insert the 6-pin and 4-pin plugs coming out of the fan unit into the said connectors. (3) Connect the two connectors of the fan unit wires and the switch wires. RMO series...
-
Page 29: Installing Fan Unit
(M3 x 5) on the right and left sides. *Please pull out the signal or optional cables (cords) before installing the rack mount cover through the opening. (See the orange circle in the figure below.) RMO series... -
Page 30: Wiring Fan Unit Of Rmo-133H-Rk/Rk2/Rk3
Confirm that the rack mount cover and fan unit are secured to the rack holder, and connect the supplied AC cable to the AC inlet of the fan unit. And then, connect the plug to the outlet prepared beforehand. *RMO-133H-RK2/RK3 can supply power to all the power supplies to be installed. RMO series... -
Page 31: Accessories
The blank panels are used to cover the gap created when less power supply units than the numbers to be installed. In RMO series, some deflections could occur at the bottom of the unit depending on the type and quantity of the power supply units to be installed. Using the blank panel will reduce the deflections. -
Page 32: Rmo-133H-Rk/Rk2/Rk3 (Rk-80/R4K-80/R4K-36 Series )
Align and secure the blank panel in two places as follows. 5-2-2 RMO-133H-RK400 (RK series: 400W/800W/1200W) Align and secure the blank panel in two places as follows. 5-2-3 RMO-133H-CO (CO series) Align and secure the blank panel in two places as follows. RMO series... -
Page 33: Rmo-150H-B (Es Series)
5 Accessories 5-2-4 RMO-150H-B (ES series) Align and secure the blank panel in two places as follows. 5-2-5 RMO-133H-DRJ (DRJ series) Align and secure the blank panel in two places as follows. RMO series... -
Page 34: Rmo-177H-R4G (R4G Series)
5 Accessories 5-2-6 RMO-177H-R4G (R4G series) Align and secure the blank panel in two places as follows. RMO series... -
Page 35: Rmo-133H-Epr (Epr Series)
5 Accessories 5-2-7 RMO-133H-EPR (EPR series) Align and secure the blank panel in two places as follows. 5-2-8 RMO-150H-EJC (EJC series) Align and secure the blank panel in two places as follows. RMO series... -
Page 36: Rmo-44H-Half (Rekj Series)
(M3 x 8) in three places. *Install the blank panel so that the folded side of the blank panel is on the REKJ series power supply unit. *For using a single unit of REKJ/VOLJ series, you must use the blank panel for installation. RMO series... - Page 37 Revision History Rev. No. Rev. Date Revision Contents 2008/10 First edition Updated the English version to the latest Japanese. 2022/07 Removed an accessory, changed an appearance diagram, added descriptions. 2023/04...
- Page 39 RMO series...
Need help?
Do you have a question about the RMO Series and is the answer not in the manual?
Questions and answers